Two eccentric cams provide a nearly unlimited range of adjustments for height, cast and rotation. Locks positively to hold your settings. Fifteen mounting holes let you position the recoil pad exactly right, so you get the best possible fit to match your shooting needs.
Dos cams excéntricos proporcionan un rango casi ilimitado de ajustes para la altura, el desplazamiento lateral y la rotación. Se bloquea de manera positiva para mantener tus ajustes. Quince orificios de montaje te permiten posicionar la almohadilla de retroceso exactamente donde la necesitas, para que consigas el mejor ajuste posible que se adapte a tus necesidades de tiro.
ESPECIFICACIONES: Aluminio, acabado mate. Cams de acero inoxidable. 6-1/8" (15.5cm) de alto, 2" (5cm) de ancho. 1½" (3.8cm) vertical, .72" (18.2mm) horizontal. Añade 3/8" (9.5mm) a la longitud de la culata. Incluye tornillos de montaje y llaves hexagonales.
Más...
Evaluaciones de clientes para GRACO CORP ADJUSTABLE PAD PLATE SILVER ALUMINUM
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 4,5
Positive Adjustment(05/10/2009)
Typical work involved in installing like any other adjustable. Adjustment is a bit more hassle than single point but stays put once set with no slippage. Weight was some concern put comes down nicely after cutting to pad and stock. Rotation is limited but normal 3/8 to 1/2 inch toe out is no problem.
BETTER THAN AN ADJUSTABLE COMB(14/10/2009)
AFTER DOING SEVERAL INSTALLATIONS, IV'E FOUND A COUPLE TRICKS TO MAKE THINGS EASIER. 1 SPRAY WD40 ON THE 80GRIT PAPER FOR 1ST CUT TO SPEED CUTTING AND STOP SOME OF THE CLOGGING, 2ND I USE MACHINIST BLACK ON THE SIDE TO BE SCRIBED SO I CAN SEE THE GRINDING LINE BETTER.I FINISH SAND WITH A BELT SANDER,USING 220 GRIT GOING WITH THE PEICE TO REMOVE ALL SANDING LINES AND THEN PUT ON THE BUFFER TO BRING TO A BRIGHT FINISH. LOOKS GREAT AND WORKS GREAT.
N.º de producto: 352000002 GRACO CORP ADJUSTABLE PAD PLATE SILVER ALUMINUM Ref Fabricante: 580 Dos cams excéntricos proporcionan un rango casi ilimitado de ajustes para la altura, el desplazamiento lateral y la rotación. Se bloquea de manera positiva para mantener tus ajustes. Quince orificios de montaje te permiten posicionar la almohadilla de retroceso exactamente donde la necesitas, para que consigas el mejor ajuste posible que se adapte a tus necesidades de tiro.
Two eccentric cams provide a nearly unlimited range of adjustments for height, cast and rotation. Locks positively to hold your settings. Fifteen mounting holes let you position the recoil pad exactly right, so you get the best possible fit to match your shooting needs.
Dos cams excéntricos proporcionan un rango casi ilimitado de ajustes para la altura, el desplazamiento lateral y la rotación. Se bloquea de manera positiva para mantener tus ajustes. Quince orificios de montaje te permiten posicionar la almohadilla de retroceso exactamente donde la necesitas, para que consigas el mejor ajuste posible que se adapte a tus necesidades de tiro.
ESPECIFICACIONES: Aluminio, acabado mate. Cams de acero inoxidable. 6-1/8" (15.5cm) de alto, 2" (5cm) de ancho. 1½" (3.8cm) vertical, .72" (18.2mm) horizontal. Añade 3/8" (9.5mm) a la longitud de la culata. Incluye tornillos de montaje y llaves hexagonales.
Más...
Evaluaciones de clientes para GRACO CORP ADJUSTABLE PAD PLATE SILVER ALUMINUM
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 4,5
Positive Adjustment(05/10/2009)
Typical work involved in installing like any other adjustable. Adjustment is a bit more hassle than single point but stays put once set with no slippage. Weight was some concern put comes down nicely after cutting to pad and stock. Rotation is limited but normal 3/8 to 1/2 inch toe out is no problem.
BETTER THAN AN ADJUSTABLE COMB(14/10/2009)
AFTER DOING SEVERAL INSTALLATIONS, IV'E FOUND A COUPLE TRICKS TO MAKE THINGS EASIER. 1 SPRAY WD40 ON THE 80GRIT PAPER FOR 1ST CUT TO SPEED CUTTING AND STOP SOME OF THE CLOGGING, 2ND I USE MACHINIST BLACK ON THE SIDE TO BE SCRIBED SO I CAN SEE THE GRINDING LINE BETTER.I FINISH SAND WITH A BELT SANDER,USING 220 GRIT GOING WITH THE PEICE TO REMOVE ALL SANDING LINES AND THEN PUT ON THE BUFFER TO BRING TO A BRIGHT FINISH. LOOKS GREAT AND WORKS GREAT.