The Geissele Gas Block Pin Punch set are made speccifically for the removal and installation of the 0.078" roll pin that secures the gas tube to the gas block on an AR-15/AR-308. Removal of a rusted in gas block roll pin has always been a challenge. The Geissele punch set make gas block work a whole lot easier.
Más...
El set de punzones Geissele Gas Block Pin Punch está diseñado específicamente para la extracción e instalación del pasador de 0.078" que asegura el tubo de gas al bloque de gas en un AR-15/AR-308. La extracción de un pasador de bloque de gas oxidado siempre ha sido un desafío. El conjunto de punzones de Geissele hace que el trabajo con el bloque de gas sea mucho más fácil.
Más...
Evaluaciones de clientes para GEISSELE AUTOMATICS GAS BLOCK PUNCH KIT FOR AR-15/AR-10
Número de evaluaciones: 3
De brownells.com: 3
Evaluación media: 3,3
Not perfect(13/04/2016)
Bought this to help remove gas block roll pin from a JP gas block after 2000 rounds. The starter punch worked great, got the pin moving. Switched to the other punch to finish driving the roll pin out. After it was out, I inspected the punch and it was slightly bent, after jut one use.
Effective Tools (16/04/2017)
I use these punches to remove gas block roll pins on M-16s and M-4s on a regular basis. I have found these tools to be effective for this task.
ok for removing roll pins not installing(21/04/2018)
these are both flat ended punches not roll pin punches. I was able to easily remove the roll pin that I was installing after it became mushroomed and deformed and was unusable. I assumed that a gas block punch kit would have a roll pin punch this was an incorrect assumption but one that set my build back because now I have to get a new roll pin and a proper roll pin punch event though I already bought an expensive gas block punch kit. If you are looking to remove a pin this is good but if you need to install one get a proper roll pin punch set.
N.º de producto: 100015137 GEISSELE AUTOMATICS GAS BLOCK PUNCH KIT FOR AR-15/AR-10 Ref Fabricante: 15-172817953020005 El set de punzones Geissele Gas Block Pin Punch está diseñado específicamente para la extracción e instalación del pasador de 0.078" que asegura el tubo de gas al bloque de gas en un AR-15/AR-308. La extracción de un pasador de bloque de gas oxidado siempre ha sido un desafío. El conjunto de punzones de Geissele hace que el trabajo con el bloque de gas sea mucho más fácil.
41.9EUR041,90 €
*
Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.
El kit de punzones Geissele está diseñado para la extracción e instalación del pasador de 0.078" en AR-15/AR-308.
Facilita el trabajo con bloques de gas, especialmente con pasadores oxidados.
Fabricado en acero, tamaño 5/64 in, estilo Punch.
Atributos
Estilo:
Punch
Material:
Steel
Talla:
5/64 in
Peso de entrega: 0,064kgAltura de envío: 19mmAncho de envío: 19mmLongitud de envío: 178mm
UPC
: 817953020005
Detalles del artículo
Hecho en USA
¡Facilita la instalación del pasador de gas en tu AR-15/AR-10! 🔧 El kit de punzones Geissele es perfecto para ti.
The Geissele Gas Block Pin Punch set are made speccifically for the removal and installation of the 0.078" roll pin that secures the gas tube to the gas block on an AR-15/AR-308. Removal of a rusted in gas block roll pin has always been a challenge. The Geissele punch set make gas block work a whole lot easier.
Más...
El set de punzones Geissele Gas Block Pin Punch está diseñado específicamente para la extracción e instalación del pasador de 0.078" que asegura el tubo de gas al bloque de gas en un AR-15/AR-308. La extracción de un pasador de bloque de gas oxidado siempre ha sido un desafío. El conjunto de punzones de Geissele hace que el trabajo con el bloque de gas sea mucho más fácil.
Más...
Evaluaciones de clientes para GEISSELE AUTOMATICS GAS BLOCK PUNCH KIT FOR AR-15/AR-10
Número de evaluaciones: 3
De brownells.com: 3
Evaluación media: 3,3
Not perfect(13/04/2016)
Bought this to help remove gas block roll pin from a JP gas block after 2000 rounds. The starter punch worked great, got the pin moving. Switched to the other punch to finish driving the roll pin out. After it was out, I inspected the punch and it was slightly bent, after jut one use.
Effective Tools (16/04/2017)
I use these punches to remove gas block roll pins on M-16s and M-4s on a regular basis. I have found these tools to be effective for this task.
ok for removing roll pins not installing(21/04/2018)
these are both flat ended punches not roll pin punches. I was able to easily remove the roll pin that I was installing after it became mushroomed and deformed and was unusable. I assumed that a gas block punch kit would have a roll pin punch this was an incorrect assumption but one that set my build back because now I have to get a new roll pin and a proper roll pin punch event though I already bought an expensive gas block punch kit. If you are looking to remove a pin this is good but if you need to install one get a proper roll pin punch set.