Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

VOLQUARTSEN
REMINGTON 597 TARGET HAMMER

810162011321 930000019

Reduces Pull Weight To Improve Accuracy

Fully machined from A2 tool steel with the hammer notch individually, surface ground to ensure an exact angle of engagement. Reduces felt trigger pull by up to 50 percent. Drop-in installation; use in an unaltered, factory triggerguard. Fits both the .22LR and .22WMR.

SPECS: A2 tool steel, in the white. Hardened to Rc 58.

Más...

Reduce el Peso del Disparador para Mejorar la Precisión

Totalmente mecanizado en acero para herramientas A2 con la muesca del martillo pulida individualmente en superficie para asegurar un ángulo exacto de acoplamiento. Reduce la sensación de peso del gatillo hasta en un 50 por ciento. Instalación directa; usar en un guardamonte de fábrica sin alterar. Apto tanto para .22LR como para .22WMR.

ESPECIFICACIONES: Acero para herramientas A2, sin acabado. Endurecido a Rc 58.

Más...

Evaluaciones de clientes para VOLQUARTSEN TARGET HAMMER

Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 5

Worth the Effort (22/07/2010)

Just finished installing the hammer. Initial trigger pull approx. 4 1/2 lbs. according to spring gauge. After installation: 2 lbs. Minimal creep. Took about 15-20 minutes. Remove trigger housing from receiver by removing the one retaining pin at rear of trigger housing(if bolt is closed, may have to pull back slightly to get housing to pop free). Place housing in padded vice at a slight angle to avoid crushing mag release button. Housing is composite so easy does it. Tap out hammer pin with punch but just enough to release hammer-don't drive out all the way. Don't remove punch but leave in pin hole to keep spring and plastic bushing in place(there are two plastic bushings inside of spring on both sides of hammer). Remove old hammer and slide in new one, align pin holes and reinstall hammer pin. You may find that you cannot get the hammer to go to the cocked position. If this is so, you have to push the trigger fully forward and the hammer should stay in the cocked position now. Install housing back into receiver and replace the one retaining pin. Install upper assembly back into stock and your done. With gun empty, check to make sure rifle fires after bolt is cycled. Mine functioned flawlessly. If you completed the job without ending up with a bunch of extra parts, you should be very pleased with the results.

Money well spent!! (03/06/2011)

If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!

BUY IT (25/12/2011)

Easy to install.
Reduces triger pull.
Smoother trigger.
Buy it. You will love it.

Great Prodct!! (17/01/2012)

Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.

Need to have in your Remington 597 (13/11/2013)

I'm very pleased about this product, really surpised about how it works overrided my spectatives, my Rem597 is in a new level of trigger and shooting control. Very fast shipping and a real proffesional package. My first but not my last buy with brownells. Thanks a lot.

Effective Solution (02/12/2013)

This was the perfect solution for the VERY heavy trigger on my daughter's 597. Easy to install; but be patient with the pin for the hammer.

Now the pull is crisp and light, with no creep. Trigger pull was reduced by more than 50%

This product was very cost effective compared to some of the other solutions out there.

High Quality Product!

great product (02/09/2014)

This hammer combined with a Brownell's extractor made an otherwise misfiring and jamming gun shoot flawlessly. I was able to shoot four different types of ammo totaling about 400 rounds without any FTE or FTF. This gun out of the box did not function properly. Now it shoots great and is extremely accurate. A must upgrade for any Remington 597 owner!

YouTube Video helps (13/05/2016)

My 597 has a great barrel, but a lousy trigger. Getting the most out of your gun comes right down to the trigger. Why do you think benchrest shooters use 4 - 6 Oz. triggers. So I ordered this item with my fingers crossed. Got it promptly and installed it in 45 minutes. Use Youtube video (9min ) and it is very straight forward. End result Trigger pull 3 1/4 - 3 1/2 Lbs.

Now to get to the range.

Leer 8 mas calificaciones en brownells.com

79.9 79.9 1 EUR

N.º de producto: 930000019
VOLQUARTSEN TARGET HAMMER
Ref Fabricante: VCRTH 810162011321 Totalmente mecanizado en acero para herramientas A2 con la muesca del martillo pulida individualmente en superficie para asegurar un ángulo exacto de acoplamiento. Reduce la sensación de peso del gatillo hasta en un 50 por ciento. Instalación directa; usar en un guardamonte de fábrica sin alterar. Apto tanto para .22LR como para .22WMR.

79.9 EUR 5 79,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Hacer: Remington Modelo: 597

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

El martillo está completamente mecanizado en acero para herramientas A2 y endurecido a Rc 58, con la muesca pulida para un ángulo de acoplamiento exacto.
Reduce la sensación de peso del gatillo hasta en un 50%, mejorando significativamente la precisión del disparo.
Es fácil de instalar directamente en un guardamonte de fábrica sin necesidad de modificaciones y es apto para calibres .22LR y .22WMR.

Atributos

Hacer: Remington Modelo: 597 Peso de entrega: 0,014kg Altura de envío: 8mm Ancho de envío: 71mm Longitud de envío: 86mm UPC : 810162011321

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.c

Operador económico responsable según el reglamento de la UE

Brownells España
P.I Molí d'en Xec / C.Barneda, 30
08291 Ripollet
España
info@brownells.es

Mejora tu precisión con el martillo Volquartsen para Remington 597 🎯. Reduce el peso del gatillo y disfruta de una instalación fácil.

Reduces Pull Weight To Improve Accuracy

SPECS: A2 tool steel, in the white. Hardened to Rc 58.

Más...

Reduce el Peso del Disparador para Mejorar la Precisión

ESPECIFICACIONES: Acero para herramientas A2, sin acabado. Endurecido a Rc 58.

Más...

Evaluaciones de clientes para VOLQUARTSEN TARGET HAMMER

Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 5

Worth the Effort (22/07/2010)

Money well spent!! (03/06/2011)

If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!

BUY IT (25/12/2011)

Easy to install.
Reduces triger pull.
Smoother trigger.
Buy it. You will love it.

Great Prodct!! (17/01/2012)

Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.

Need to have in your Remington 597 (13/11/2013)