Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

BOONIE PACKER PRODUCTS
AR-15/M16 IMPROVED REDI-MAG

100004455

Holds Spare Magazine On The Receiver For Ultra-Fast Reloads

Don’t lose precious seconds in competition or combat fumbling for a spare magazine during a reload. This rugged speed loading system clamps directly to the lower receiver of any AR-15/M16 rifle or carbine and securely holds a second, fully loaded magazine alongside the mag well for super-fast mag changes. More reliable and easier to use than improvised methods, like taping two magazines together, that can cause malfunctions at critical moments. Closed-top design protects the spare mag from rain, dirt, dust, and debris and prevents the top round from jumping forward under recoil. Independent release system lets you drop the spare mag and the mag in the weapon separately to allow tactical reloads and greater flexibility in clearing malfunctions. Bolt Catch Extension (BCE) mounts directly to the factory bolt catch and lets you release the bolt, with or without the Redi-Mag attached to the gun, simply by slapping the BCE with an open palm. Installation requires no permanent alterations to receiver or mag well. Designed for mil-spec receivers; may not fit custom billet receivers. Steel model available in Standard configuration model that enables faster installation and removal of the entire Redi-Mag from the weapon.

SPECS: Steel, Parkerized, or 6061 T6 aluminum, hardcoat anodized, both dark gray, with reinforced molded polymer BCE and spacer. 3½" (8.9cm) long, 2½" (6.4cm) wide, 2¾" (7cm) high. Weight: 8.4 oz. (234g) (steel), 5.6 oz. (159 g) (aluminum). Fits AR-15/M16/M4 rifles and carbines with standard forged lower receiver.

Más...

Sujeta un Cargador de Repuesto en el Receptor para Recargas Ultra-Rápidas

No pierdas segundos preciosos en competiciones o combates buscando un cargador de repuesto durante la recarga. Este robusto sistema de carga rápida se sujeta directamente al receptor inferior de cualquier rifle o carabina AR-15/M16 y mantiene de forma segura un segundo cargador completamente cargado junto al pozo del cargador para cambios de mag super rápidos. Más fiable y fácil de usar que métodos improvisados, como pegar dos cargadores juntos, que pueden causar fallos en momentos críticos. El diseño cerrado protege el cargador de repuesto de la lluvia, la suciedad, el polvo y los escombros y evita que la primera bala salte hacia adelante por el retroceso. El sistema de liberación independiente te permite soltar tanto el cargador de repuesto como el cargador en el arma por separado para permitir recargas tácticas y mayor flexibilidad al despejar fallos. La Extensión del Retén del Cerrojo (BCE) se monta directamente en el retén del cerrojo de fábrica y te permite liberar el cerrojo, con o sin el Redi-Mag acoplado al arma, simplemente golpeando el BCE con la palma abierta. La instalación no requiere alteraciones permanentes en el receptor o el pozo del cargador. Diseñado para receptores mil-spec; puede no encajar en receptores billet personalizados. Modelo de acero disponible en configuración estándar que permite una instalación y desmontaje más rápidos del Redi-Mag completo del arma.

ESPECIFICACIONES: Acero, Parkerizado, o aluminio 6061 T6, anodizado duro, ambos de color gris oscuro, con BCE de polímero moldeado reforzado y separador. 3½" (8.9cm) de largo, 2½" (6.4cm) de ancho, 2¾" (7cm) de alto. Peso: 8.4 oz. (234g) (acero), 5.6 oz. (159 g) (aluminio). Compatible con rifles y carabinas AR-15/M16/M4 con receptor inferior forjado estándar.

Más...

Evaluaciones de clientes para BOONIE PACKER PRODUCTS IMPROVED REDI-MAG, STANDARD STEEL

Número de evaluaciones: 10
De brownells.com: 10
Evaluación media: 4,1

Solid mount (09/11/2009)

If you want to have a spare mag solidly attached to the weapon this is the way to go.

Unlike pouches or rail mounted mag holders this allows the user to have a spare in a very natural spot.

Perfect for when you are required to be condition 4 but want to have a mag ready to go (LE/Military). Great for 3 gun or carbine matches or anywhere a quick reload is needed.

The bolt release button is a bit small but a solid smack with the heel of your hand to the side of the receiver will send the bolt forward anyway.

Great Product (13/11/2009)

Gives you a spare mag without having to mess with pouches. You're hand doesn't have to leave the rifle for more than a couple of seconds. Does not work well with PMAGs since they only have a small indent.

excellent upgrade for operators (24/12/2009)

THE MOST useful accessory i have added to my carbine.
works well with BAD lever as well
there is nothing quite like picking up my carbine 24/7 with 60 rounds attached to it.

Fast/Tactical reload a must? Get this! (13/06/2011)

This product is GREAT! Hands down. It keeps a fully loaded mag right next to the one in the gun. Just hold the full one, drop the empty and switch 'em. Left handed AR owner? Works just fine for us (yes, I'm one too)though it's not a must, I would recommend the Magpul B.A.D Lever. It works with the Redi-Mag and makes it a lot easier to operate the bold release.

very useful (27/06/2011)

Mine has been in service on my duty rifle for over 10yrs. No problems whatsoever. Would definitley buy again. Some things are "cool". This item is USEFUL.

Best addon since an optic (16/12/2011)

I run the Redimag on my patrol rifle. I am not an AR junkie that adds on every new shinny thing that comes out, I run a sling, optic, and light. I use my rifle as a tool to do my job not to look cool. The Redimag is a needed addon. No other spare mag carrier holds ammo as secure and deploys so rapidly. It's a must have!

A little struggling to put on, but anyone can do it. I wish the rubber gaskets that protect the AR magwell from scratches was one piece instead of three. However once its on, it's secure and greatly increases reloading speed.

installation is a pain (21/06/2012)

This thing was a PITA to install. The screw holes didn't want to line up and my Magpul BAD lever was rubbing so I had to take the Dremel tool to it. After all the hassle getting it on my lower I found it doesn't like LMT MRP uppers. The Redi-Mag hits the area just behind the barrel screws. I was able to get the upper mounted, but its pushing the Redi-Mag out just a enough that the flared floor plates on my Pmags are touching. It doesn't look like it'll be enough to stop a mag from dropping free but time will tell.

Must have for tactical reloads (24/06/2013)

I've had this on my AR15 for well over 10 years and it's the old version. Once you are adapted to it, you will find you are the fastest guy on the line as your backup mag is right with you. Has never failed to drop the mag. Simply grab the reload mag before you punch the mag release and as the empty mag drops free, slide in your backup mag. It does make your gun heavier but doesn't seem to affect the balance. I'm ordering a new aluminum RediMag for a new gun. Works with BAD lever, another must have.

Mag ready (01/09/2017)

I've been thinking of getting this for years. I was concerned the steel would be too heavy. After installing I picked up the ar and realized it wasn't bad at all. Besides once you install a full mag "it's heavy!" Installation was pretty simple. I used a small clamp to hold the screw section together to install the screws though it did come with a screw and nut to do the same thing. The worst part was the nylon nuts. That was a bit of a PITA but with the right tools still hardly an issue. I use 20 rounders for general SD since I'm not in LE. Im also left handed and it worked well for me. A little practice and mag changes were quick and easy. I'll keep practicing to make sure it's second nature. I'm going to install another on my house SBR. HIGHLY RECOMMENDED.

Will not fit commercial lowers (26/11/2017)

This will only fit lowers that have a removable trigger guard. It will not fit lowers that have a molded in trigger guard as many commercial lowers do.

Leer 10 mas calificaciones en brownells.com

149.9 149.9 1 EUR

N.º de producto: 100004455
BOONIE PACKER PRODUCTS IMPROVED REDI-MAG, STANDARD STEEL
Ref Fabricante: RMMKI No pierdas segundos preciosos en competiciones o combates buscando un cargador de repuesto durante la recarga. Este robusto sistema de carga rápida se sujeta directamente al receptor inferior de cualquier rifle o carabina AR-15/M16 y mantiene de forma segura un segundo cargador completamente cargado junto al pozo del cargador para cambios de mag super rápidos. Más fiable y fácil de usar que métodos improvisados, como pegar dos cargadores juntos, que pueden causar fallos en momentos críticos. El diseño cerrado protege el cargador de repuesto de la lluvia, la suciedad, el polvo y los escombros y evita que la primera bala salte hacia adelante por el retroceso. El sistema de liberación independiente te permite soltar tanto el cargador de repuesto como el cargador en el arma por separado para permitir recargas tácticas y mayor flexibilidad al despejar fallos. La Extensión del Retén del Cerrojo (BCE) se monta directamente en el retén del cerrojo de fábrica y te permite liberar el cerrojo, con o sin el Redi-Mag acoplado al arma, simplemente golpeando el BCE con la palma abierta. La instalación no requiere alteraciones permanentes en el receptor o el pozo del cargador. Diseñado para receptores mil-spec; puede no encajar en receptores billet personalizados. Modelo de acero disponible en configuración estándar que permite una instalación y desmontaje más rápidos del Redi-Mag completo del arma.

149.9 EUR 14 149,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Color: Dark Gray Hacer: AR-15

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

El AR-15/M16 Improved Redi-Mag permite cambios de cargador ultra rápidos al mantener un segundo cargador junto al pozo del cargador.
El diseño cerrado protege el cargador de repuesto de elementos como lluvia, suciedad y polvo, y evita fallos críticos.
La Extensión del Retén del Cerrojo (BCE) facilita la liberación del cerrojo sin necesidad de alterar permanentemente el receptor o el pozo del cargador.

Atributos

Color: Dark Gray Hacer: AR-15 Peso de entrega: 0,249kg Altura de envío: 33mm Ancho de envío: 112mm Longitud de envío: 109mm

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.x

Optimiza tus recargas con el AR-15/M16 Improved Redi-Mag ✨. Rápido, seguro y diseñado para condiciones exigentes. ¡Mejora tu equipo hoy!

Holds Spare Magazine On The Receiver For Ultra-Fast Reloads

Más...

Sujeta un Cargador de Repuesto en el Receptor para Recargas Ultra-Rápidas

Más...

Evaluaciones de clientes para BOONIE PACKER PRODUCTS IMPROVED REDI-MAG, STANDARD STEEL

Número de evaluaciones: 10
De brownells.com: 10
Evaluación media: 4,1

Solid mount (09/11/2009)

Great Product (13/11/2009)

excellent upgrade for operators (24/12/2009)

THE MOST useful accessory i have added to my carbine.
works well with BAD lever as well
there is nothing quite like picking up my carbine 24/7 with 60 rounds attached to it.

Fast/Tactical reload a must? Get this! (13/06/2011)

very useful (27/06/2011)

Mine has been in service on my duty rifle for over 10yrs. No problems whatsoever. Would definitley buy again. Some things are "cool". This item is USEFUL.

Best addon since an optic (16/12/2011)

installation is a pain (21/06/2012)

Must have for tactical reloads (24/06/2013)

Mag ready (01/09/2017)

Will not fit commercial lowers (26/11/2017)

This will only fit lowers that have a removable trigger guard. It will not fit lowers that have a molded in trigger guard as many commercial lowers do.

Leer 10 mas calificaciones en brownells.com