Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

FULTON ARMORY
M14/M1A SIMULATED FULL-AUTO SELECTOR LEVER

100005279

Fills the Gap In The Stock & Gives A Semi-Auto Rifle A "Full-Auto" Look

One-piece simulated selector lever made of Parkerized steel fits in the selector lever cutout in USGI and aftermarket M14 stocks to give your rifle the authentic appearance of a full-auto capable GI M14. Fills the unsightly gap and helps keep dirt and debris out of the action. Rotates to semi- or full-auto position. Installs on the stock, not the receiver perfectly legal.

SPECS: Steel, Parkerized, matte black. Fits USGI and aftermarket M14 rifle stocks with selector lever cutout. Mounting hardware included. Minor fitting required.

Más...

Rellena el Espacio en la Culata y Da al Rifle Semi-Automático un Aspecto de "Automático Completo"

La palanca simuladora de selector de disparo de una sola pieza hecha de acero Pavonado encaja en el recorte del selector de disparo en culatas M14 de USGI y del mercado secundario para darle a tu rifle la apariencia auténtica de un M14 GI capaz de disparo automático. Rellena el espacio antiestético y ayuda a mantener la suciedad y los escombros fuera del mecanismo. Rota a la posición de semi- o automático completo. Se instala en la culata, no en el receptor, completamente legal.

ESPECIFICACIONES: Acero, Pavonado, negro mate. Compatible con culatas de rifle M14 de USGI y del mercado secundario con recorte para selector de disparo. Incluye herrajes de montaje. Requiere ajuste menor.

Más...

Evaluaciones de clientes para FULTON ARMORY SIMULATED SELECTOR LEVER

Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 4,2

Looks good In GI stock (30/06/2011)

Installed in my GI stock in about 2 min. Looks really good and thoroughly blokes the unsightly hole.

Not a perfect fit (29/07/2011)

I had to grind quite a bit of metal off the leading edge to get this to fit the cutout on my GI stock, and also slightly relieve the wood around the handle bolster. The roll pin used to connect the handle to the body of the switch didn't go all the way through the assembly. Once put in place it looked good, and filled the cutout well.

It's like chrome wheels for you car (10/01/2013)

I have one of them on each of my three rifles. On one rifle, I had to relieve the top portion that fits under the receiver. I filed in down and that was it. The other two fit perfectly. I guess its the difference in the stocks. I was checking my targets one day and turned around to see the Range Officer burying his face into my rifle. I asked him if he was looking for a date. He was looking at the auto switch and saw the receiver said M14. An hour later the sheriff arrived and asked to see the rifle. They look that good! It makes the rifle! Before you drill any holes, make sure it isn't touching the receiver.

I love this but.... (05/01/2014)

Today, we attempted to install 3 of these, we were able to get two to fit. The third one did not fit because we were attempting to use it on a rare Devine Texas M1a. The receiver is different and some metal will need to be removed from the switch. Rule number 1, always modify the cheapest part.

To begin with, no instructions come with the switch. That isn't a bad thing, first see if the switch will fit your rifle by installing it with using the screw and roll pin. If the receiver closes then you are good to go. You can save yourself all kinds of problems by drilling the hole for the roll pin larger, I think that the pin is too big as it comes from the factory.

You are going to have to use a drill no matter what! You need to pre-drill the holes for the roll pin and screw in the wood. Install the roll pin first, remount your receiver and position the switch and check for clearance. I would not attempt to install without using a drill.

Why mess with epoxy? (25/03/2016)

The simulated selector lever dropped right in on my walnut GI M14 stock. Make sure you use the correct size drill bits for drilling into the stock for the screw and pin. I used the selector as a template and drilled the hole for the screw mount first then slightly screwed in the mounting screw into the stock to hold the selector in place. Next I drilled the pin hole into the stock to the appropriate depth and lightly tapped the pin into place with my brass faced punch hammer. Then tightened the wood screw to complete the install. The final results are a much more professional/realistic looking vs the epoxy fillers that never match the stock

Leer 5 mas calificaciones en brownells.com

114.9 114.9 1 EUR

N.º de producto: 100005279
FULTON ARMORY SIMULATED SELECTOR LEVER
Ref Fabricante: FA-M-093 La palanca simuladora de selector de disparo de una sola pieza hecha de acero Pavonado encaja en el recorte del selector de disparo en culatas M14 de USGI y del mercado secundario para darle a tu rifle la apariencia auténtica de un M14 GI capaz de disparo automático. Rellena el espacio antiestético y ayuda a mantener la suciedad y los escombros fuera del mecanismo. Rota a la posición de semi- o automático completo. Se instala en la culata, no en el receptor, completamente legal.

114.9 EUR 2 114,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Hacer: Springfield Modelo: M14, M1A

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

La palanca simuladora de selector de disparo de una sola pieza hecha de acero Pavonado encaja en culatas M14 de USGI y del mercado secundario.
Rellena el espacio antiestético y ayuda a mantener la suciedad y los escombros fuera del mecanismo, rotando a la posición de semi- o automático completo.
Se instala en la culata, no en el receptor, y es completamente legal.

Atributos

Hacer: Springfield Modelo: M14,M1A Peso de entrega: 0,045kg Altura de envío: 23mm Ancho de envío: 71mm Longitud de envío: 135mm

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.x

Mejora tu M14 con la palanca simuladora de Fulton Armory ✨. Diseño auténtico, fácil de instalar y legal. ¡Haz que tu rifle destaque!

Fills the Gap In The Stock & Gives A Semi-Auto Rifle A "Full-Auto" Look

SPECS: Steel, Parkerized, matte black. Fits USGI and aftermarket M14 rifle stocks with selector lever cutout. Mounting hardware included. Minor fitting required.

Más...

Rellena el Espacio en la Culata y Da al Rifle Semi-Automático un Aspecto de "Automático Completo"

Más...

Evaluaciones de clientes para FULTON ARMORY SIMULATED SELECTOR LEVER

Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 4,2

Looks good In GI stock (30/06/2011)

Installed in my GI stock in about 2 min. Looks really good and thoroughly blokes the unsightly hole.

Not a perfect fit (29/07/2011)

It's like chrome wheels for you car (10/01/2013)

I love this but.... (05/01/2014)

Why mess with epoxy? (25/03/2016)

Leer 5 mas calificaciones en brownells.com

FULTON ARMORY
M14/M1A SIMULATED FULL-AUTO SELECTOR LEVER

Evaluaciones de clientes para FULTON ARMORY SIMULATED SELECTOR LEVER

Top takeaways

Atributos

Detalles del artículo

Evaluaciones de clientes para FULTON ARMORY SIMULATED SELECTOR LEVER

Conéctese a

Métodos de pago seguros

Asociaciones profesionales

Bienvenido.

FULTON ARMORY M14/M1A SIMULATED FULL-AUTO SELECTOR LEVER

Evaluaciones de clientes para FULTON ARMORY SIMULATED SELECTOR LEVER

Top takeaways

Atributos

Detalles del artículo

Evaluaciones de clientes para FULTON ARMORY SIMULATED SELECTOR LEVER

Conéctese a

Métodos de pago seguros

Asociaciones profesionales

Bienvenido.

FULTON ARMORY
M14/M1A SIMULATED FULL-AUTO SELECTOR LEVER