Lightens trigger pull and cocking effort for fast, accurate shooting. Open center retains durability of factory spring, gives consistent, uniform, spring tension.
SPECS: Spring steel. Colt/EMF fits Colt Cowboy and Single Action Army, EMF Hartford. Uberti fits private-label, SAA clones made by Uberti. May require minor fitting.
Más...
Diseño Único que Suaviza la Acción y Reduce el Esfuerzo del Disparador
Aligera el esfuerzo de disparo y amartillado para un tiro rápido y preciso. El centro abierto mantiene la durabilidad del muelle de fábrica, proporcionando una tensión constante y uniforme.
ESPECIFICACIONES: Acero para muelles. Compatible con Colt Cowboy y Single Action Army de Colt, EMF Hartford. Uberti es adecuado para clones de SAA de marca privada fabricados por Uberti. Puede requerir un ajuste menor.
Más...
Evaluaciones de clientes para WOLFF COLT/EMF MAINSPRING
Número de evaluaciones: 3
De brownells.com: 3
Evaluación media: 3,7
Just Right(09/07/2013)
At first, I tried the Lee Gunslinger spring set in my 3rd generation Colt SAA which is chambered in 45 Colt. The springs made the action feel sweet but light primer hits were a problem with the Remington large pistol primers I use. I ordered the Wolff mainspring and kept the wire trigger spring from the Lee set. I think I have a great combination now as the hammer is still lighter to pull than with the factory spring and the gun feels very "slick". I love the feel of my Colt SAA with the Wolff mainspring. It installed easily without any fitting and ordering from Brownell's is always a pleasure.
Also works in an Uberti 1858 Remington(22/10/2013)
I bought this spring for use with a Taylor's conversion cylinder. It fit my Uberti Remington perfectly. The action is much smoother, and the cylinder's firing pins are no longer getting battered.
WILL NOT FIT my EMF !!!(08/06/2015)
I ordered this for an EMF Hartford 45 Colt. There was an obvious problem as the length was way too short ! The overall length falls between the factory spring and the length of a factory
N.º de producto: 969322800 WOLFF COLT/EMF MAINSPRING Ref Fabricante: 32280 Aligera el esfuerzo de disparo y amartillado para un tiro rápido y preciso. El centro abierto mantiene la durabilidad del muelle de fábrica, proporcionando una tensión constante y uniforme.
33.9EUR1033,90 €
*
Plazo de entrega de aproximadamente 14-21 días.
Caracteristicas:Hacer: ColtModelo: Single Action Army
Hacer:
Colt
Modelo:
Single Action Army
Peso de entrega: 0,014kgAltura de envío: 13mmAncho de envío: 69mmLongitud de envío: 137mm
Detalles del artículo
Hecho en USA
N.º de producto: 969322850 WOLFF UBERTI MAINSPRING Ref Fabricante: 32285 Aligera el esfuerzo de disparo y amartillado para un tiro rápido y preciso. El centro abierto mantiene la durabilidad del muelle de fábrica, proporcionando una tensión constante y uniforme.
Lightens trigger pull and cocking effort for fast, accurate shooting. Open center retains durability of factory spring, gives consistent, uniform, spring tension.
SPECS: Spring steel. Colt/EMF fits Colt Cowboy and Single Action Army, EMF Hartford. Uberti fits private-label, SAA clones made by Uberti. May require minor fitting.
Más...
Diseño Único que Suaviza la Acción y Reduce el Esfuerzo del Disparador
Aligera el esfuerzo de disparo y amartillado para un tiro rápido y preciso. El centro abierto mantiene la durabilidad del muelle de fábrica, proporcionando una tensión constante y uniforme.
ESPECIFICACIONES: Acero para muelles. Compatible con Colt Cowboy y Single Action Army de Colt, EMF Hartford. Uberti es adecuado para clones de SAA de marca privada fabricados por Uberti. Puede requerir un ajuste menor.
Más...
Evaluaciones de clientes para WOLFF COLT/EMF MAINSPRING
Número de evaluaciones: 3
De brownells.com: 3
Evaluación media: 3,7
Just Right(09/07/2013)
At first, I tried the Lee Gunslinger spring set in my 3rd generation Colt SAA which is chambered in 45 Colt. The springs made the action feel sweet but light primer hits were a problem with the Remington large pistol primers I use. I ordered the Wolff mainspring and kept the wire trigger spring from the Lee set. I think I have a great combination now as the hammer is still lighter to pull than with the factory spring and the gun feels very "slick". I love the feel of my Colt SAA with the Wolff mainspring. It installed easily without any fitting and ordering from Brownell's is always a pleasure.
Also works in an Uberti 1858 Remington(22/10/2013)
I bought this spring for use with a Taylor's conversion cylinder. It fit my Uberti Remington perfectly. The action is much smoother, and the cylinder's firing pins are no longer getting battered.
WILL NOT FIT my EMF !!!(08/06/2015)
I ordered this for an EMF Hartford 45 Colt. There was an obvious problem as the length was way too short ! The overall length falls between the factory spring and the length of a factory