Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

SEEKINS PRECISION
SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

811452029309 100018841

90 degree standard throw lever 60 degree short throw lever Available in black Drop in replacement for Mil-Spec selector switch Fully ambidextrous Not recommended to be used with the Hipertouch trigger

Más...

Palanca de accionamiento estándar de 90 grados Palanca de accionamiento corto de 60 grados Disponible en negro Reemplazo directo para el interruptor selector Mil-Spec Completamente ambidiestro No se recomienda su uso con el gatillo Hipertouch

Más...

Evaluaciones de clientes para SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

Número de evaluaciones: 6
De brownells.com: 6
Evaluación media: 3,5

Loose fit (11/03/2016)

There is a 3/32" gap between the receiver and the safety lever on each side of the receiver. Almost slips over the stops on the receiver. Also, the anodizing on one of the levers is purple instead of black. I will be returning this. This is the first Seekins product I have ever had an issue with.

Great product (29/03/2016)

Super easy to install, especially liked the way you can switch the controls to be 60 or 90 degrees just by turning over the base. Way better pricing than other versions on the market.

Well made, easy install, good fit. (23/03/2017)

Purchased two of these in black. Installed one in a Palmetto AR9 and the other in a Palmetto AR15. Both went in without difficulty, look good, and operate well. I shoot left-handed and this product makes manipulating the safety much easier.

Didn't fit on two different rifles. (27/04/2017)

This is my 3rd Seekins ambi safety and I've been pleased up to this point. The first two I purchased were installed on Palmetto State Armory lowers and they went in and function without issue. Based on those experiences I purchased a 3rd Seekins for use on a factory Daniel Defense rifle. The safety seems a bit overlarge in diameter as it was very tight when inserted in the first hole in the receiver, and could not be pushed all the way to the other side. I then tried to install the safety on a factory Armalite rifle, and again would not fit. Fortunately I had another rifle with a Palmetto receiver that had a CAA ambi safety installed. I removed the CAA and installed the Seekins in the Palmetto without difficulty. The CAA safety was then installed in the Armalite rifle without difficulty. I could have done a bit of careful fitting and probably gotten the Seekins to fit in the Armalite and Daniel Defense but I don't really want to be sanding on an anodized part.

Maybe not. (04/06/2017)

Safety was mot mil spec diameter. Would not fit at all in hole, when standard mil spec single selector safety dropped right in. Had to auger it into both holes so it milled out some of the aluminum lower receiver. Finally took an emery cloth to it and filed it down on both ends of the shaft. Put the lower together and it wouldn't go full 12 o'clock to release the trigger without using your thumb to give it that extra millimeter(s). Bad tetent channel maybe? Took it out and reversed it so it's now a short throw.... now it works, but a lot or work and not a cheap safety for the trouble it gave me.

Suprised! (13/12/2017)

I did not actually read the product description nor reviews when i ordered it. I thought it was just a regular ambi safety with fancy arms. When i got it, i realized that it has 2 safety groove cut in it, 1 side is the regular 90 degree cut and the other side is 60 degree short throw cut. That is a bonus for me as i have both regular marked lowers and 60 degree sts marked lowers.

I did not experienced any fitment issue that other reviewers have. It fitted my Noveske, aero precision, armalite and spike tactical lowers. It is a tighter fit in my Noveske, which i believe has everything to do with the fact that Noveske cerakote and anodize all their lowers.

I will be buying a few more of these.

Leer 6 mas calificaciones en brownells.com

104.9 104.9 1 EUR

N.º de producto: 100018841
SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK
Ref Fabricante: 11580002 811452029309 Palanca de accionamiento estándar de 90 grados Palanca de accionamiento corto de 60 grados Disponible en negro Reemplazo directo para el interruptor selector Mil-Spec Completamente ambidiestro No se recomienda su uso con el gatillo Hipertouch

104.9 EUR 0 104,90 € *

Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.

Caracteristicas: Hacer: AR-15

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Atributos

Hacer: AR-15 Peso de entrega: 0,018kg Altura de envío: 6mm Ancho de envío: 83mm Longitud de envío: 108mm UPC : 811452029309

Detalles del artículo

Hecho en USA
Clasificación de exportación de EE. UU.: 0A501.x

Mejora tu AR-15 con el Safety Selector Kit ambidiestro de Seekins Precision. 🔧 Disponible en negro y fácil de instalar.

Más...

Evaluaciones de clientes para SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

Número de evaluaciones: 6
De brownells.com: 6
Evaluación media: 3,5

Loose fit (11/03/2016)

Great product (29/03/2016)

Super easy to install, especially liked the way you can switch the controls to be 60 or 90 degrees just by turning over the base. Way better pricing than other versions on the market.

Well made, easy install, good fit. (23/03/2017)