Cartucho: 6.5 x 55 mm Swedish Mauser, 300 Winchester Magnum, 338 Winchester Magnum, 7 mm Remington Magnum, 225 Winchester, 8 mm Remington Mag, 7 mm STW, 30 Remington AR, 264 Winchester MagnumN.º de producto: 749011485
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.
N.º de producto: 749011485
N.º fabr.: 0910250
050806111325 Los Inserts del Bump Gage de Sinclair se utilizan para medir la cantidad de retroceso del hombro al configurar los dies de tamaño completo. Nuestros Bump Gages se instalan en cualquiera de nuestros cuerpos de comparador y están mecanizados para ajustarse a ángulos de hombro particulares de los cartuchos. En lugar de medir hasta la línea de datum, estos gages indican desde el hombro del cartucho para obtener una medición más precisa y fácil de evaluar de cuánto estás dimensionando realmente tus cartuchos. Normalmente recomendamos entre .001" y .002" de retroceso para rifles de cerrojo y entre .003" y .005" para rifles tipo AR-15. También es una herramienta útil para mantener tu brass y munición cargada separados si tienes múltiples rifles recamarados para el mismo cartucho y para verificar la munición cargada.
Cartucho: 6.5 x 55 mm Swedish Mauser, 300 Winchester Magnum, 338 Winchester Magnum, 7 mm Remington Magnum, 225 Winchester, 8 mm Remington Mag, 7 mm STW, 30 Remington AR, 264 Winchester MagnumN.º de producto: 749011485
Sinclair Bump Gage Inserts are used to measure the amount of shoulder bump when setting up full length sizing dies. Our Bump Gages install in either of our comparator bodies and are machined to fit particular shoulder angles of cartridges. Rather than measuring to the datum line, these gages indicate off of the shoulder of the case to get a better, more easily assessable measurement of how much you are actually sizing your cases. We usually recommend between .001" to .002" bump for bolt action rifles and between .003" and .005" for AR-15 type rifles. Also a useful tool for keeping your brass and loaded ammunition separated if you have multiple rifles chambered for the same cartridge and checking loaded ammunition.
Los Inserts del Bump Gage de Sinclair se utilizan para medir la cantidad de retroceso del hombro al configurar los dies de tamaño completo. Nuestros Bump Gages se instalan en cualquiera de nuestros cuerpos de comparador y están mecanizados para ajustarse a ángulos de hombro particulares de los cartuchos. En lugar de medir hasta la línea de datum, estos gages indican desde el hombro del cartucho para obtener una medición más precisa y fácil de evaluar de cuánto estás dimensionando realmente tus cartuchos. Normalmente recomendamos entre .001" y .002" de retroceso para rifles de cerrojo y entre .003" y .005" para rifles tipo AR-15. También es una herramienta útil para mantener tu brass y munición cargada separados si tienes múltiples rifles recamarados para el mismo cartucho y para verificar la munición cargada.
Top takeaways
Los Sinclair Bump Gage Inserts se utilizan para medir el ajuste del hombro en matrices de tamaño completo.
Recomendados para rifles de acción de cerrojo (.001" a .002") y rifles tipo AR-15 (.003" a .005").
Compatibles con varios calibres de cartucho, incluyendo 6.5 x 55 mm Swedish Mauser y 300 Winchester Magnum.
Atributos
Cartucho:300 Winchester Magnum,6.5 x 55 mm Swedish Mauser,225 Winchester,30 Remington AR,7 mm STW,264 Winchester Magnum,8 mm Remington Mag,7 mm Remington Magnum,338 Winchester Magnum
Peso de entrega:0,023kg
Ancho de envío:83mm
Longitud de envío:146mm
UPC:050806111325
Detalles del artículo
Hecho en USA
Opiniones de clientes
Calificaciones de clientes (17)
3,1 / 5
No recomendable
Does not work for 6.5 Creedmoor 24/07/2018
Bought this 30A to check bumping the shoulders of my 6.5 Creedmoor brass. Had been using a Wilson Case gage to do the job and it works well I thought this may be faster. I bumped and bumped no reading beyond the initial cal of 1.501 on the digital calipers. Each bump i got a new reading on the Wilson Case Gage. Highly disappointed with the purchase.
Claramente recomendable
Quality 20/06/2018
I have the original Stoney Point tool and this fits and works well on .338 Lapua Magnum cases to adjust the amount of shoulder bump on cases.
Ligeramente recomendable
Nicely machined doesnât fit without mods 18/04/2018
Iâm using this to measure shoulder bump between fired and full length sized cases. The âthrough holeâ is much too tight on all the 223 fires cases Iâve tried, this leads to cases sticking and readings of .010+ greater than normal. I can neck size to get them to fit but this is an additional step that Iâd prefer not to do, and is impossible to accomplish if Iâm trying to get data while on the range. I asked Sinclairâs techs if there was an issue with the product and they told me to ream it out with a drill bit. Not exactly the answer I was looking for. I would like to keep using this product because I like that the opening matches up with the shoulder angle unlike competing products, but it doesnât work out of the box.
No recomendable
Poor / Inaccurate Description 03/03/2018
Does NOT fit 300 Blackout without modification.
No recomendable
Incorrect fitment 24/02/2018
The details on this part say this fits 300 Blackout. Turns out it doesn't unless you modify it does not explain that anywhere in the description.
Ligeramente recomendable
Feels Like Plastic 26/01/2017
I thought the product was made of metal, which is should be. Feels like plastic, which it should not be. I didn't have much luck with this product and the inserts using it as a bump gauge. The readings were inconsistent even with two different calipers. Even trying to bump .308 cases back 4/1000ths for an AR10 was nearly impossible to do with any consistency. The finished products did not shoot as well as a fully resized cases in the testing I did.
No recomendable
Only works with certain calipers 13/12/2016
We use Aero Space brand calipers at the EPA. The slot on these arent wide enough to fit over them. That's OK but Sinclair should list some models they work with OR the width of the slot.
Claramente recomendable
Quality Construction 18/07/2016
The bump gauge/comparator body has quality construction, and hold the inserts well. They attach to my calipers securely, and work well.
Claramente recomendable
great product 01/03/2016
I really like the insert it's made of Stainless Steel so it will not wear easy . The gauge is also very easy to use, works on my Hornady body too.
No recomendable
Does not work for .416 Rigby 25/01/2015
The .416 Rigby is a beltless cartridge that headspaces on its ample 45 degree shoulder. This bump gage hole diameter is too small to host the outside dimensions of the .416 Rigby brass. It would have been nice to know there was a size limit on the exterior brass dimensions so as to avoid a return.
Claramente recomendable
These Fit the Hornady Tools 07/01/2015
This little item told me right away what problem My sons hand loads had very easy to use and the fact they fit the Hornady tools that look like this is a big plus....If you already have the Hornady gauges.
Ligeramente recomendable
Requires honing geometry change 24/01/2014
The tapered opening is right at .277 and goes extremely far down VLD type/Accubond bullets, this makes it impossible to measure Ogive Combined Overall Length on loaded bullets. The older stainless steel hexagonal shaped comparator is much more useful as it's tapered opening is at .268". This comparator insert's tapered opening should start at .270" within .001" of that.
Claramente recomendable
Great tool for measuring shoulder bump 13/12/2013
I bought this tool to use with the Sinclair XL Comparator body and it works great! I am able to measure the distance between the should and the base of a fire cartridge and then set my sizing die to bump the shoulder back a certain distance. I would definitely buy this tool again.
Claramente recomendable
Great tool for measuring bullets/cases 13/12/2013
I bought this tool in order to measure bullets from the ojive to the base and also to measure should bump. It's a high quality tool and works perfectly for my needs. Being that it's the XL version, you're able to measure shoulders with a bullets installed.
No recomendable
Poor discription 02/07/2012
It's listed as "30-06 Family" but will not work with 17deg shoulders over 338 cal.
Claramente recomendable
Much Better than Hornady LNL inserts 23/02/2011
It's much easier to measure headspace with an insert that's tapered to match the cartridge's shoulder angle. Easier to use than the 90 deg. edge of the straight hole drilled in the original Hornady LNL inserts.
Claramente recomendable
Keep it simple 09/02/2011
Simplicity is more often than not the best way to do things...This product is so simple but is something every shooter should have at their reloading bench. Use it every few hundred rounds to make sure your desired bullet jump matches wear in barrel.
Operador económico responsable según el reglamento de la UE
Brownells España
P.I Molí d'en Xec / C.Barneda, 30
08291 Ripollet
España
info@brownells.es
Vistos recientemente
¡Ups! Algo salió mal.
Hemos encontrado un error al cargar este contenido. Actualice la página para continuar. Si el problema persiste, póngase en contacto con nuestro servicio de atención al cliente.
*
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.