No-Mar Brass Rod Knocks Stuck Bullets Out Of Bores
Don't let a stuck bullet from a "squib" or weak load cut short a shooting session. Far superior to other rods or makeshift punches, this non-marring brass rod fits the bore closely, can't wedge between bullet nose and rifling. Each rod is drilled and tapped to thread onto a Dewey cleaning rod; very handy for knocking stuck bullets out of rifle barrels.
SPECS: Kit contains one of each size rod and (2) 8-32 to 12-28 adapters. 8" (20.3cm) long. Brass. Pak has 2 rods of size listed and 2 Dewey 30A rod adapters.
Más...
Varilla de Latón No-Mar Para Sacar Balas Atascadas de los Cañones
No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
ESPECIFICACIONES: El kit contiene uno de cada tamaño de varilla y (2) adaptadores de 8-32 a 12-28. 8" (20.3cm) de largo. Latón. El paquete tiene 2 varillas del tamaño listado y 2 adaptadores de varilla Dewey 30A.
Más...
Evaluaciones de clientes para BROWNELLS 45 CALIBER SQUIB ROD 8" LONG 2 PACK
Número de evaluaciones: 7
De brownells.com: 7
Evaluación media: 3,3
Saved my Model 10(31/05/2010)
Got out my progressive press after a few years and loaded up some wadcutters. Went out to the range to test them. After a few rounds, my gun locked up. I could see a bullet lodged between the cylinder and the forcing cone. Took the gun home and got out my squib rod kit. Followed the directions, took out the mainspring and hammer. I measured the the squib rod in the barrel and them tapped it with a plastic hammer. A few taps later, the cylinder opened and I was able to remove the cartridge and bullet. It appears there was no powder, just a primer in this one; a hazard of using a progressive. Saved me a trip to the gunsmith. If you shoot more than one caliber, buy the whole kit. "Be prepared."
fits and works(04/04/2016)
These fit and work well. You need one of these in your tools and range bag.
Can't fit a 40SW barrel(05/08/2013)
It is too tight and can't fit any of my 40SW STI barrels.
Too big.(04/04/2016)
I returned a set that were too big to go down the barrel with a comment on the appropriate diameter. The replacement set is also too big.
In order to fit easily down the barrel they should be .385, plus or minus. .389 is apparently the absolute max diameter to fit inside the rifling. The first set was .392. The second set was .390.
Somebody's tolerances are not being checked.
Don't Buy(11/05/2016)
This is the third set of .40 squib rods that will not work. They will just fit down a Glock barrel but will not fit down a .40 S&W M/P barrel (tried it in multiple different pistols). If you really want them, plan on turning them down yourself to a diameter that works in your pistol.
Squibb Rod Is Essential Safety Tool(25/09/2012)
I use the Brownell's Squibb Rod Kit often in my duties as a range safety officer to clear bore obstructions and to dislodge stuck cases.
A bullet stuck in the bore, caused by inadvertently loading and attempting to fire a round with primer-only and no powder can be a serious hazard if not properly handled. A few drops of Kroil down the bore quickly reduce adhesion of a stuck jacketed bullet with the bore. The appropriate size squibb rod and adapter are threaded onto the Dewey cleaning rod and the obstruction tapped out the breech by multiple light taps of the rod only. No hammer is needed.
Occasionally you experience a stuck case in an AR which cannot be removed by pulling the charging handle. With the muzzle pointed in a safe direction, and the breech cover open, place the squibb rod against the bolt carrier and rap with a mallet to drive the bolt carrier to the rear, unlocking the bolt so that the jammed round or case can be removed safely.
A bullet-in-bore malfunction in a revolver often jams the cylinder, so that it cannnot be opened. A wrap with the squibb rod quickly and easily drives the stuck bullet back into the cylinder, clear of the forcing cone, so that the range can be declared clear.
To determine the proper size of cast bullet to load in an antique military or cowboy rifle it is necesssary to upset a throat "slug" to measure the diameter of the forcing cone ahead of the chamber. This is done by filling a sized case up to its mouth with molten lead from the casting pot, then filing the lead flush. Chamber an inch long piece of bore-diameter, soft, pure-lead wire in from of the lead-filled case, and use the Brownell squibb rod to upset the slug so that it conforms to the forcing cone and throat. Knock out the upset slug with a fired case from your rifle to send to the mold maker.
A must have if you like to shoot!(11/03/2013)
I purchased this set a little while back. I have had 2 squibs(1-45, 1-40) since and they were factory loads. No tool box should be without them. They work PERFECT, easy to use, already paid for itself. THANKS!
N.º de producto: 084175045 BROWNELLS 45 CALIBER SQUIB ROD 8" LONG 2 PACK Ref Fabricante: 45SQUIBROD050806031395 No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
54.9EUR054,90 €
*
Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.
Varillas de latón de 8" para remover balas atascadas, sin dañar el cañón.
Compatibles con varillas de limpieza Dewey, incluyen adaptadores 8-32 a 12-28.
Especialmente diseñadas para armas de calibre 45 (.451-.454), paquete contiene 2 varillas y 2 adaptadores.
Atributos
Calibre:
45 Caliber (.451-.454)
Hacer:
Universal Handguns
Peso de entrega: 0,34kgAltura de envío: 13mmAncho de envío: 61mmLongitud de envío: 229mm
UPC
: 050806031395
Detalles del artículo
Hecho en USA
Sale
N.º de producto: 084175032 BROWNELLS 32 CALIBER SQUIB ROD 8" LONG 2 PACK No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
Varilla de latón diseñada para remover balas atascadas sin dañar el cañón.
Compatible con varillas de limpieza Dewey, incluye adaptadores de 8-32 a 12-28.
El paquete contiene dos varillas de 8" de largo y dos adaptadores Dewey 30A.
Atributos
Calibre:
30 Caliber (.308),32 Caliber (.312-.313)
Hacer:
Universal Handguns
Peso de entrega: 0,136kgAltura de envío: 13mmAncho de envío: 74mmLongitud de envío: 251mm
Detalles del artículo
Hecho en USA
N.º de producto: 084175040 BROWNELLS 10MM, 40/41 CALIBER SQUIB ROD 8" LONG 2 PACK Ref Fabricante: 10MMSQUIBROD10MMSQUIBROD No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
Varilla de latón diseñada para extraer balas atascadas sin dañar el cañón.
Compatible con varillas de limpieza Dewey, incluye adaptadores de 8-32 a 12-28.
El paquete contiene dos varillas de 8" de largo y dos adaptadores Dewey 30A.
Atributos
Calibre:
40/10 mm (.400-.401),41 Caliber (.410-.412)
Hacer:
Universal Handguns
Peso de entrega: 0,272kgAltura de envío: 13mmAncho de envío: 71mmLongitud de envío: 216mm
UPC
: 10MMSQUIBROD
Detalles del artículo
Hecho en USA
Sale
N.º de producto: 084175044 BROWNELLS 44 CALIBER SQUIB ROD 8" LONG 2 PACK No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
Varillas de latón de 8" diseñadas para sacar balas atascadas sin dañar el cañón.
Compatibles con varillas de limpieza Dewey, incluyen adaptadores de 8-32 a 12-28.
Paquete contiene 2 varillas y 2 adaptadores, ideales para rifles calibre 44.
Atributos
Calibre:
44 Caliber (.429-.430)
Hacer:
Universal Handguns
Peso de entrega: 0,363kgAltura de envío: 8mmAncho de envío: 76mmLongitud de envío: 274mm
Detalles del artículo
Hecho en USA
Sale
N.º de producto: 084175000 BROWNELLS SQUIB ROD KIT No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
El SQUIB ROD BROWNELLS SQUIB ROD KIT está diseñado para remover balas atascadas sin dañar el cañón del rifle.
Incluye varillas de latón perforadas y roscadas que se pueden enroscar en una varilla de limpieza Dewey, facilitando su uso.
El kit contiene varillas de diferentes tamaños y adaptadores de 8-32 a 12-28, ofreciendo versatilidad y compatibilidad con varios rifles.
Atributos
Hacer:
Universal Handguns
Peso de entrega: 0,658kgAltura de envío: 10mmAncho de envío: 53mmLongitud de envío: 262mm
Detalles del artículo
Hecho en USA
Sale
N.º de producto: 084175357 BROWNELLS 9MM, 38/357 CALIBER SQUIB ROD 8" LONG 2 PACK Ref Fabricante: 9MMSQUIBROD No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
La varilla de latón no daña el cañón y se ajusta estrechamente, evitando atascos entre la bala y las estrías.
Incluye adaptadores para enroscarse en una varilla de limpieza Dewey, ideal para rifles.
El paquete contiene dos varillas de 8" y dos adaptadores de 8-32 a 12-28.
Atributos
Calibre:
38/357 Caliber (.357-.359),9 mm (.355-.356)
Hacer:
Universal Handguns
Peso de entrega: 0,204kgAltura de envío: 10mmAncho de envío: 74mmLongitud de envío: 221mm
Detalles del artículo
Hecho en USA
¡No dejes que un squib arruine tu tiro! 🛠️ Con las varillas de latón de Brownells, retira balas atascadas de forma segura y eficiente.
No-Mar Brass Rod Knocks Stuck Bullets Out Of Bores
Don't let a stuck bullet from a "squib" or weak load cut short a shooting session. Far superior to other rods or makeshift punches, this non-marring brass rod fits the bore closely, can't wedge between bullet nose and rifling. Each rod is drilled and tapped to thread onto a Dewey cleaning rod; very handy for knocking stuck bullets out of rifle barrels.
SPECS: Kit contains one of each size rod and (2) 8-32 to 12-28 adapters. 8" (20.3cm) long. Brass. Pak has 2 rods of size listed and 2 Dewey 30A rod adapters.
Más...
Varilla de Latón No-Mar Para Sacar Balas Atascadas de los Cañones
No permitas que una bala atascada por un "squib" o una carga débil interrumpa una sesión de tiro. Mucho mejor que otras varillas o punzones improvisados, esta varilla de latón no daña el cañón, se ajusta estrechamente al mismo y no puede quedar atascada entre la punta de la bala y las estrías. Cada varilla está perforada y roscada para enroscarse en una varilla de limpieza Dewey; muy práctica para sacar balas atascadas de los cañones de rifles.
ESPECIFICACIONES: El kit contiene uno de cada tamaño de varilla y (2) adaptadores de 8-32 a 12-28. 8" (20.3cm) de largo. Latón. El paquete tiene 2 varillas del tamaño listado y 2 adaptadores de varilla Dewey 30A.
Más...
Evaluaciones de clientes para BROWNELLS 45 CALIBER SQUIB ROD 8" LONG 2 PACK
Número de evaluaciones: 7
De brownells.com: 7
Evaluación media: 3,3
Saved my Model 10(31/05/2010)
Got out my progressive press after a few years and loaded up some wadcutters. Went out to the range to test them. After a few rounds, my gun locked up. I could see a bullet lodged between the cylinder and the forcing cone. Took the gun home and got out my squib rod kit. Followed the directions, took out the mainspring and hammer. I measured the the squib rod in the barrel and them tapped it with a plastic hammer. A few taps later, the cylinder opened and I was able to remove the cartridge and bullet. It appears there was no powder, just a primer in this one; a hazard of using a progressive. Saved me a trip to the gunsmith. If you shoot more than one caliber, buy the whole kit. "Be prepared."
fits and works(04/04/2016)
These fit and work well. You need one of these in your tools and range bag.
Can't fit a 40SW barrel(05/08/2013)
It is too tight and can't fit any of my 40SW STI barrels.
Too big.(04/04/2016)
I returned a set that were too big to go down the barrel with a comment on the appropriate diameter. The replacement set is also too big.
In order to fit easily down the barrel they should be .385, plus or minus. .389 is apparently the absolute max diameter to fit inside the rifling. The first set was .392. The second set was .390.
Somebody's tolerances are not being checked.
Don't Buy(11/05/2016)
This is the third set of .40 squib rods that will not work. They will just fit down a Glock barrel but will not fit down a .40 S&W M/P barrel (tried it in multiple different pistols). If you really want them, plan on turning them down yourself to a diameter that works in your pistol.
Squibb Rod Is Essential Safety Tool(25/09/2012)
I use the Brownell's Squibb Rod Kit often in my duties as a range safety officer to clear bore obstructions and to dislodge stuck cases.
A bullet stuck in the bore, caused by inadvertently loading and attempting to fire a round with primer-only and no powder can be a serious hazard if not properly handled. A few drops of Kroil down the bore quickly reduce adhesion of a stuck jacketed bullet with the bore. The appropriate size squibb rod and adapter are threaded onto the Dewey cleaning rod and the obstruction tapped out the breech by multiple light taps of the rod only. No hammer is needed.
Occasionally you experience a stuck case in an AR which cannot be removed by pulling the charging handle. With the muzzle pointed in a safe direction, and the breech cover open, place the squibb rod against the bolt carrier and rap with a mallet to drive the bolt carrier to the rear, unlocking the bolt so that the jammed round or case can be removed safely.
A bullet-in-bore malfunction in a revolver often jams the cylinder, so that it cannnot be opened. A wrap with the squibb rod quickly and easily drives the stuck bullet back into the cylinder, clear of the forcing cone, so that the range can be declared clear.
To determine the proper size of cast bullet to load in an antique military or cowboy rifle it is necesssary to upset a throat "slug" to measure the diameter of the forcing cone ahead of the chamber. This is done by filling a sized case up to its mouth with molten lead from the casting pot, then filing the lead flush. Chamber an inch long piece of bore-diameter, soft, pure-lead wire in from of the lead-filled case, and use the Brownell squibb rod to upset the slug so that it conforms to the forcing cone and throat. Knock out the upset slug with a fired case from your rifle to send to the mold maker.
A must have if you like to shoot!(11/03/2013)
I purchased this set a little while back. I have had 2 squibs(1-45, 1-40) since and they were factory loads. No tool box should be without them. They work PERFECT, easy to use, already paid for itself. THANKS!