Professionally And Easily Replace Stripped-Out Bushing Holes-No Welding Or Drilling
Easily and professionally solves the problem of stripped out stock bushing holes. Special tap cleans out stripped frame threads, cuts new ones without pre-drilling. Matching bushing screws right in, uses original grip screw. Will save your life when polishing/bluing, accurizing .45's!
SPECS: Bushings - .255"-60, blued steel. Tap - High speed.
Más...
Reemplaza profesional y fácilmente los agujeros de casquillos desgastados - Sin soldadura ni taladrado
Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
ESPECIFICACIONES: Casquillos - .255"-60, acero azulado. Macho de roscar - Alta velocidad.
Más...
Evaluaciones de clientes para BROWNELLS 1911 AUTO OVERSIZED BUSHING TAP
Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 4,5
This tap is not for amateurs(26/03/2011)
I am very dissapointed in the results of using this tool. I followed instructions and was very careful to keep everything aligned. The bushing installed with this tool were cocked. This makes it hard to put the pistol grips on and the bushing threads will probably get buggered again because of not being seated properly.Not to mentioned I screwed up a new Kimber TLE .45 receiver.
The problem is that the hole size of the standard bushing is .235 and the tip of the tap is .240 inches. This means you will not get traction till you're 3/4 way through the hole and by that time you will not be aligned perpendicular. The final hole size for the bushing is .255 inches.
The solution is to make the tip of the tap to be about .230 inche not .240. If you don't have a drill press using this tool you are not going to like the results.
Worked fine(01/05/2012)
The tap worked fine. Used it on a Kimber CDP in hand tap wrench. Bushings screwed in tight and square. Had no problem getting it started through the existing hole.
A Good Product And Worth The Money(08/05/2014)
Easy to use in a 1/4" tap wrench. I had to replace grip bushings in my Springfield Champion. This Oversized Grip Bushing Tap worked very well. Easy to do job. It strips the old threads out , then makes new ones. Good to have in the gunsmithing tools.
works just fine(02/06/2011)
I had a grip bushing strip out on a Kimber Pro Carry - I had neglected to check the bushings regularly for tightness and paid the price. A tip on re-tapping without getting the hole crooked: Cut out a 1" by 1" block from a .75" board. Drill a hole (with a drill-press) in the block just big enough for the tap to pass through without wiggling around. Use the block as a guide to keep the tap perpendicular to the frame of the gun while re-tapping. Holding the block in place with finger pressure was easy for an aluminum frame. For a steel frame that is a little harder to get the tap started into, a C clamp may be required to hold the block steady. One last thing - for an aluminum frame 1911 I wouldn't recommend staking the bushing after install, as the bushing itself is harder than the frame and it can still work loose in time. A SMALL amount of JB Weld holds the bushing in place for good, while leaving the bushing and threads undamaged for future removal if necessary.
Great tool!(23/05/2015)
I used this kit on my Kimber Pro CDP II. Worked very well! Chucked bit in hand-held T handle. Using a small block of wood with a perpendicular hole drilled through it the size of the tap, helps to keep the tap at 90 degrees to the work surface.
When I describe myself as a Gunsmith, I mean AMATURE gunsmith. So when I say "easy to use" it's easy.
Perfect tool/bushing solution!(17/04/2017)
I have a Kimber Raptor that came from the factory with a cross-threaded grip bushing, discovered when the grip came loose after about 100 rounds. I tried getting the original bushing back in correctly, thought it held but then it just broke loose again next trip to the range.
I was pretty concerned I'd have to send the thing back to Kimber to get fixed up until I found this oversize tap/bushing set. The PERFECT solution, super easy to use with some care as people people noted to keep the tap going straight. With this aluminum frame gun it cut nice new threads in minutes.
Adding to the others tips, I used a bit of Loctite instead of JB Weld, hopefully that holds, but the intent is the same since the bushing is actually harder than the frame I didn't think staking it was a good idea. Also, I'd screw in the bushing just with fingers, no tools, to make sure you don't accidentally cross-thread it. These threads are so so very fine it would be easy to do, and especially with an aluminum frame easy to damage those new threads. I put it in finger-tight until it bottoms out then use a screwdriver to cinch it up.
Thanks Brownells!
Great solution for stripped bushing(24/06/2017)
Extremely easy to use. Reluctant at first to attempt to repair a stripped out grip bushing on my 1911. Great product.
Back in action(12/09/2017)
Had 2 stripped grip bushings (discovered when I went to install my grip). Ordered this off others reviews, and was NOT disappointed. 2 holes tapped, new bushings installed and grips installed in less than 15 minutes (by hand. Tapped the old holes with a hand tap and this bit). Works like a charm if you have stripped GI bushings!!!
N.º de producto: 080598225 BROWNELLS 1911 AUTO OVERSIZED BUSHING TAP Ref Fabricante: 41539050806018822 Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
El macho de roscar especial limpia los hilos desgastados y corta nuevos sin necesidad de pre-taladrar.
El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip.
Ideal para el mantenimiento y reparación de pistolas 1911, especialmente modelos Government, Commander y Officers.
Atributos
Estilo:
Bushing
Hacer:
1911
Material:
Steel
Modelo:
Commander,Government,Officers
Peso de entrega: 0,014kgAncho de envío: 83mmLongitud de envío: 146mm
UPC
: 050806018822
Detalles del artículo
Hecho en USA
Operador económico responsable según el reglamento de la UE
Brownells España
P.I Molí d'en Xec / C.Barneda, 30
08291 Ripollet
España
info@brownells.es
N.º de producto: 080570000 BROWNELLS 1911 BASIC OVERSIZED BUSHING SET 4 BUSHINGS & 1 TAP050806015838 Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
N.º de producto: 080571100 BROWNELLS 1911 DELUXE OVERSIZED BUSHING SET 24 BUSHINGS & 1 TAP050806015845 Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
N.º de producto: 080572012 BROWNELLS 1911 45 CALIBER OVERSIZED STOCK BUSHINGS 4 PACK050806015852 Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
N.º de producto: 080572025 BROWNELLS 1911 45 CALIBER OVERSIZED STOCK BUSHINGS 24 PACK050806015869 Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
N.º de producto: 080572050 BROWNELLS 1911 45 CALIBER OVERSIZED STOCK BUSHINGS 48 PACK050806015876 Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
Professionally And Easily Replace Stripped-Out Bushing Holes-No Welding Or Drilling
Easily and professionally solves the problem of stripped out stock bushing holes. Special tap cleans out stripped frame threads, cuts new ones without pre-drilling. Matching bushing screws right in, uses original grip screw. Will save your life when polishing/bluing, accurizing .45's!
SPECS: Bushings - .255"-60, blued steel. Tap - High speed.
Más...
Reemplaza profesional y fácilmente los agujeros de casquillos desgastados - Sin soldadura ni taladrado
Resuelve fácil y profesionalmente el problema de los agujeros de los casquillos del stock desgastados. El macho de roscar especial limpia los hilos desgastados del armazón, corta nuevos sin necesidad de pre-taladrar. El casquillo correspondiente se enrosca directamente, utilizando el tornillo original del grip. ¡Te salvará la vida cuando estés puliendo/azulando, precisando pistolas .45!
ESPECIFICACIONES: Casquillos - .255"-60, acero azulado. Macho de roscar - Alta velocidad.
Más...
Evaluaciones de clientes para BROWNELLS 1911 AUTO OVERSIZED BUSHING TAP
Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 4,5
This tap is not for amateurs(26/03/2011)
I am very dissapointed in the results of using this tool. I followed instructions and was very careful to keep everything aligned. The bushing installed with this tool were cocked. This makes it hard to put the pistol grips on and the bushing threads will probably get buggered again because of not being seated properly.Not to mentioned I screwed up a new Kimber TLE .45 receiver.
The problem is that the hole size of the standard bushing is .235 and the tip of the tap is .240 inches. This means you will not get traction till you're 3/4 way through the hole and by that time you will not be aligned perpendicular. The final hole size for the bushing is .255 inches.
The solution is to make the tip of the tap to be about .230 inche not .240. If you don't have a drill press using this tool you are not going to like the results.
Worked fine(01/05/2012)
The tap worked fine. Used it on a Kimber CDP in hand tap wrench. Bushings screwed in tight and square. Had no problem getting it started through the existing hole.
A Good Product And Worth The Money(08/05/2014)
Easy to use in a 1/4" tap wrench. I had to replace grip bushings in my Springfield Champion. This Oversized Grip Bushing Tap worked very well. Easy to do job. It strips the old threads out , then makes new ones. Good to have in the gunsmithing tools.
works just fine(02/06/2011)
I had a grip bushing strip out on a Kimber Pro Carry - I had neglected to check the bushings regularly for tightness and paid the price. A tip on re-tapping without getting the hole crooked: Cut out a 1" by 1" block from a .75" board. Drill a hole (with a drill-press) in the block just big enough for the tap to pass through without wiggling around. Use the block as a guide to keep the tap perpendicular to the frame of the gun while re-tapping. Holding the block in place with finger pressure was easy for an aluminum frame. For a steel frame that is a little harder to get the tap started into, a C clamp may be required to hold the block steady. One last thing - for an aluminum frame 1911 I wouldn't recommend staking the bushing after install, as the bushing itself is harder than the frame and it can still work loose in time. A SMALL amount of JB Weld holds the bushing in place for good, while leaving the bushing and threads undamaged for future removal if necessary.
Great tool!(23/05/2015)
I used this kit on my Kimber Pro CDP II. Worked very well! Chucked bit in hand-held T handle. Using a small block of wood with a perpendicular hole drilled through it the size of the tap, helps to keep the tap at 90 degrees to the work surface.
When I describe myself as a Gunsmith, I mean AMATURE gunsmith. So when I say "easy to use" it's easy.
Perfect tool/bushing solution!(17/04/2017)
I have a Kimber Raptor that came from the factory with a cross-threaded grip bushing, discovered when the grip came loose after about 100 rounds. I tried getting the original bushing back in correctly, thought it held but then it just broke loose again next trip to the range.
I was pretty concerned I'd have to send the thing back to Kimber to get fixed up until I found this oversize tap/bushing set. The PERFECT solution, super easy to use with some care as people people noted to keep the tap going straight. With this aluminum frame gun it cut nice new threads in minutes.
Adding to the others tips, I used a bit of Loctite instead of JB Weld, hopefully that holds, but the intent is the same since the bushing is actually harder than the frame I didn't think staking it was a good idea. Also, I'd screw in the bushing just with fingers, no tools, to make sure you don't accidentally cross-thread it. These threads are so so very fine it would be easy to do, and especially with an aluminum frame easy to damage those new threads. I put it in finger-tight until it bottoms out then use a screwdriver to cinch it up.
Thanks Brownells!
Great solution for stripped bushing(24/06/2017)
Extremely easy to use. Reluctant at first to attempt to repair a stripped out grip bushing on my 1911. Great product.
Back in action(12/09/2017)
Had 2 stripped grip bushings (discovered when I went to install my grip). Ordered this off others reviews, and was NOT disappointed. 2 holes tapped, new bushings installed and grips installed in less than 15 minutes (by hand. Tapped the old holes with a hand tap and this bit). Works like a charm if you have stripped GI bushings!!!