Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

WILSON COMBAT
1911 BARREL BUSHING

874218000714 965000049

Blued Or Stainless, Target Grade

Installs in most 1911 Autos with little to no fitting. O.D.’s fit nicely in most slides. Blued & stainless version may need fitting.

SPECS: #29B Blued - .825" (20.9mm) long, .575" (14.6mm) I.D., .703" (17.9mm) O.D. #29S Stainless - .825" (20.9mm) long. .578" I.D., .702" (17.8mm) O.D. #29CO Officer's Model Stainless - .700" (17.79mm) I.D., .766" (19.47mm) O.D.

Más...

Azulado o Acero Inoxidable, Calidad de Competición

Se instala en la mayoría de las pistolas 1911 con poco o ningún ajuste. Los diámetros exteriores encajan bien en la mayoría de las correderas. Las versiones azuladas y de acero inoxidable pueden necesitar ajuste.

ESPECIFICACIONES: #29B Azulado - .825" (20.9mm) de largo, .575" (14.6mm) de diámetro interior, .703" (17.9mm) de diámetro exterior. #29S Acero Inoxidable - .825" (20.9mm) de largo, .578" de diámetro interior, .702" (17.8mm) de diámetro exterior. #29CO Modelo Officer de Acero Inoxidable - .700" (17.79mm) de diámetro interior, .766" (19.47mm) de diámetro exterior.

Más...

Evaluaciones de clientes para WILSON COMBAT WILSON #29CO OFFICER'S MODEL BUSHING

Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 4,8

Lots of extra metal for a tight fitting (09/04/2011)

I had to do a couple hours of hand polishing just to get it to fit into the slide on my wife Colt Officers model 1911. After that came about 30 minutes of needle filing, trying to shape the locking lug so that it would turn in engage and stop lined up exactly with the plunger hole. I'm going to be installing a Wilson Combat full length guide rod and reverse plug kit so there is no need for the bushing to over travel like the factory. I stopped filing the locking lug before I reached the over travel position.

very useful product (11/06/2010)

i have a small custom shop,have used several of these, improves acurracy greatly,

Fitting required (14/07/2010)

I had some fitting to do , but my gun is also a Norinco with poor spec. ID and OD had to be trim and polished. Nice look and tight fit, don't forget to get a barrel wrench.

Good quality (13/03/2017)

I replaced old collet bushing in my Series 70 Colt Government with this SS Wilson Combat Bushing. The bushing to slide fit was perfect. The I.D. measured .579 and my barrel measured .580 so I hand sanded the I.D. of the bushing to .581. A day at the range showed tighter groups then I've had since I bought the pistol in early 80.s. I went from 6" groups to less then 2" at 20 yds. I suggest hand sanding over using power tools for fitting to get the best fit. Great, easy to install product. Make sure you have a bushing wrench.

1911a1 Barrel Bushing (06/01/2011)

I will say that Wilson Combat has great quality products. But, when it comes to the barrel bushing for a Springfield 1911A1 Mil-Spec to drop in, forget it. It will require some work from a gunsmith. I am a hobby gunsmith but, this is a bit advanced for me to even try to make it work when I don't have the correct tool for the job.

great product (02/11/2012)

took a bit of fitting, but now my old norinco has a bushing that requires a wrench. the barrel is also quite a bit tighter in the bushing. I cant wait to test it out as I've had great luck with there other products and cant wait to see my groups shrink.

Didn't fit my R1 (01/03/2018)

I'm sure it works fine, Wilson Combat doesn't make junk. However it did not fit my Remington R1. I was annoyed that my all blued 1911 had a stainless bushing so I ordered this one. My guess is that the Remington is out of spec rather than the other way around. I could try and have it fitted but that might take the finish off which would defeat the purpose. I'm not going to return it because it's not Brownells fault it didn't fit.

Wilson Combat 1911 Barrel Bushing (29B) (14/04/2018)

Installed this bushing on my Springfield 1911-A1. Very tight fit but finally able to get the slid to cycle freely after cycling it a few dozen times. May remove the bushing and polish the bushing ID with some 1000 grit sand paper on a wood dowel rod.

I think a snug fit bushing could help increase accuracy.

Leer 8 mas calificaciones en brownells.com

38.9 39.9 3 EUR

N.º de producto: 965000049
WILSON COMBAT WILSON #29CO OFFICER'S MODEL BUSHING
Ref Fabricante: 29CO 874218000714 Se instala en la mayoría de las pistolas 1911 con poco o ningún ajuste. Los diámetros exteriores encajan bien en la mayoría de las correderas. Las versiones azuladas y de acero inoxidable pueden necesitar ajuste.

39.9 EUR 2 39,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Acabado: Stainless Steel Estilo: Drop-In Hacer: 1911 Modelo: Officers

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Atributos

Acabado: Stainless Steel Estilo: Drop-In Hacer: 1911 Modelo: Officers Peso de entrega: 0,009kg Altura de envío: 1mm Ancho de envío: 83mm Longitud de envío: 146mm UPC : 874218000714

Detalles del artículo

Hecho en USA

N.º de producto: 965029001
WILSON COMBAT WILSON #29B BUSHING
Ref Fabricante: 29B 874218000707 Se instala en la mayoría de las pistolas 1911 con poco o ningún ajuste. Los diámetros exteriores encajan bien en la mayoría de las correderas. Las versiones azuladas y de acero inoxidable pueden necesitar ajuste.

39.9 EUR 1 39,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Acabado: Blued Estilo: Drop-In Hacer: 1911 Modelo: Government

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

N.º de producto: 965029002
WILSON COMBAT WILSON #29S BUSHING
Ref Fabricante: 29S 874218000738 Se instala en la mayoría de las pistolas 1911 con poco o ningún ajuste. Los diámetros exteriores encajan bien en la mayoría de las correderas. Las versiones azuladas y de acero inoxidable pueden necesitar ajuste.

38.9 EUR 6 38,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Acabado: Stainless Steel Estilo: Drop-In Hacer: 1911 Modelo: Government

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Mejora tu pistola 1911 con el Bushing Wilson Combat #29CO. 🔧 Ideal para el modelo Officer, fácil de instalar y compatible con la mayoría.

Blued Or Stainless, Target Grade

Installs in most 1911 Autos with little to no fitting. O.D.’s fit nicely in most slides. Blued & stainless version may need fitting.

Más...

Azulado o Acero Inoxidable, Calidad de Competición

Más...

Evaluaciones de clientes para WILSON COMBAT WILSON #29CO OFFICER'S MODEL BUSHING

Número de evaluaciones: 8
De brownells.com: 8
Evaluación media: 4,8

Lots of extra metal for a tight fitting (09/04/2011)

very useful product (11/06/2010)

i have a small custom shop,have used several of these, improves acurracy greatly,

Fitting required (14/07/2010)

I had some fitting to do , but my gun is also a Norinco with poor spec. ID and OD had to be trim and polished. Nice look and tight fit, don't forget to get a barrel wrench.

Good quality (13/03/2017)