Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

CYLINDER & SLIDE
1911 LIGHT PULL SEAR SPRING

000000000949 206000065

Reduces the trigger pull approximately 1.5lb while maintaining a safe spring pressure hammer begins to follow after installation of this spring, the hammer/sear engagement is incorrect and should be repaired. This is the same spring that we furnish in the trigger pull kits.

SPECS: For the 1911 models.

Más...

Reduce aproximadamente 1.5lb el peso del disparador manteniendo una presión segura del muelle del martillo. Si después de instalar este muelle, el martillo comienza a seguir al sear, significa que el enganche entre martillo y sear es incorrecto y debe ser reparado. Este es el mismo muelle que proporcionamos en los kits de ajuste del peso del disparador.

ESPECIFICACIONES: Para los modelos 1911.

Más...

Evaluaciones de clientes para CYLINDER & SLIDE 1911 LIGHT PULL SEAR SPRING

Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 4,6

4.5lbs Pull (29/12/2015)

Claims to reduce trigger pull 1.5lb, but from what starting trigger pull?

I already had bent my sear spring to pull 4.5lbs, I dropped this in and saw no improvement, the same pull or slightly higher pull. I would say it comes set for 4.5lb if you already polished your internals.

This is good if you are not comfortable bending your sear spring.

Great Idea, Great product (10/04/2016)

If you're not comfortable c working on the sear/hammer angle, and/or trying to adjust the sear leg of the sear spring, this is a good, safe (c caveats), and easy way to reduce trigger press. Note: I do not use these on carry 1911s unless (a) the trigger is otherwise OK but very heavy, and (b) I've worked the gun on the range enough times to be confident in it. For me, these are for primarily range use. Drops right in, of course. Use it in conjunction c a 18-20# mainspring, and be sure to replace your firing pin return spring c an extra power one. You may not need to do the latter, but it's good insurance just in case your gun might have a stock unit. Stone your trigger bar channels if you need to, Brownells sells the stone very inexpensively, as c everything else noted here. For the best trigger job, naturally, see your local gunsmith.....but this will do quite well in most cases and a lot cheaper. Be sure to test it fully, just in case. I think this product is the best thing since canned beer and peanut butter. Just sayin'.

Big improvement (26/11/2016)

Had this inserted in my Walther/Colt 1911 .22. Great improvement to trigger pull and feel. Well worth the money, even with gunsmith cost. Extremely happy with results

Excellent, easy upgrade! (03/02/2018)

Installed this and a 17lbs. main spring into a Ruger SR1911. Took a pound off the trigger pull weight. Not a two pound trigger that breaks like glass, but less than $20 and I installed them in half an hour. Watch a couple videos and anyone can do it.

Very satisfied with this spring (03/02/2018)

I installed this spring in conjunction with a 19.5 lb hammer spring and my, what a difference. I do not have a trigger pull guage, but my guess is that the two reduced the trigger pull by close to 2 lb and also reduced grittiness. My use is strictly for range/target shooting.

Leer 5 mas calificaciones en brownells.com

26.9 26.9 1 EUR

N.º de producto: 206000065
CYLINDER & SLIDE 1911 LIGHT PULL SEAR SPRING
Ref Fabricante: CS0094 000000000949 Reduce aproximadamente 1.5lb el peso del disparador manteniendo una presión segura del muelle del martillo. Si después de instalar este muelle, el martillo comienza a seguir al sear, significa que el enganche entre martillo y sear es incorrecto y debe ser reparado. Este es el mismo muelle que proporcionamos en los kits de ajuste del peso del disparador.

26.9 EUR 31 26,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Hacer: 1911 Modelo: Government, Commander, Officers

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Atributos

Hacer: 1911 Modelo: Commander,Government,Officers Peso de entrega: 0,005kg Altura de envío: 19mm Ancho de envío: 13mm Longitud de envío: 70mm UPC : 000000000949

Detalles del artículo

Hecho en USA

Operador económico responsable según el reglamento de la UE

Brownells España
P.I Molí d'en Xec / C.Barneda, 30
08291 Ripollet
España
info@brownells.es

SPECS: For the 1911 models.

Más...

ESPECIFICACIONES: Para los modelos 1911.

Más...

Evaluaciones de clientes para CYLINDER & SLIDE 1911 LIGHT PULL SEAR SPRING

Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 4,6

4.5lbs Pull (29/12/2015)

Great Idea, Great product (10/04/2016)

Big improvement (26/11/2016)

Had this inserted in my Walther/Colt 1911 .22. Great improvement to trigger pull and feel. Well worth the money, even with gunsmith cost. Extremely happy with results

Excellent, easy upgrade! (03/02/2018)