Inventory Just Two Sleeves & Fit All Types Of Stocks
Fully-adjustable bedding sleeves are easy to install and fit nearly all types and sizes of rifle stocks. Lightweight, pre-contoured adjustment rings move on a fully threaded shaft so you can size them for an exact fit without additional, time-consuming cutting, filing or machining. Sold as a pair, long for Rear screw, short for Front screw.
SPECS: Sleeve - steel, .296" (7.5mm) ID, 7/16"-20 tpi. Adjustment Ring - aluminum, .560" (14mm) OD. Front - .700" (17mm) long. Rear - 1.16" (2.9cm) long. Installation requires alterations to stock and synthetic bedding. Sold as pairs only.
Más...
Inventario Solo Dos Mangas & Se Ajustan a Todos los Tipos de Culatas
Las mangas de bedding ajustables son fáciles de instalar y se adaptan a casi todos los tipos y tamaños de culatas de rifles. Los anillos de ajuste ligeros y pre-contorneados se desplazan sobre un eje completamente roscado, permitiéndote ajustarlos para un encaje exacto sin necesidad de cortes, limados o mecanizados adicionales y que consumen tiempo. Se venden en pares, el largo para el tornillo trasero y el corto para el tornillo delantero.
ESPECIFICACIONES: Manga - acero, .296" (7.5mm) ID, 7/16"-20 tpi. Anillo de ajuste - aluminio, .560" (14mm) OD. Delantero - .700" (17mm) de largo. Trasero - 1.16" (2.9cm) de largo. La instalación requiere modificaciones en la culata y el uso de bedding sintético. Se venden únicamente en pares.
Más...
Evaluaciones de clientes para BROWNELLS ADJUSTABLE PILLAR BEDDING SLEEVE
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 5
Works great.(20/06/2012)
I used these to pillar bed a pre 64 Winchester. They are great for someone who is doing a home job. They adjust a little to easy and would move when being placed in the hole. A dab of grease on the thread where the nuts are sitting will help. Make sure you have the correct size Forstner bit. I could not find a single local store that carries this size (9/16). If I could do it again I would get the piloted Forstner bit sold by Brownells (Stock #:080-909-000WB). It is not cheap, but it cost the same as a local machinist charged me to drill the holes in my stock. You could do it with a hand drill at home but these holes must be perfectly straight or you are defeating the purpose.
Phenomenal Product!(04/08/2013)
I recently used these for the first time on a Win Model 70 Super Grade, CRF, made in the 80's out of the CT plant. I have used Brownell's Acraglass Gel with steel ferrels for pillars for years on other rifles, but decided to try these adjustable pillars for this project. As the previous reviewer stated, getting the holes drilled precisely is critical. I used a 1/2" bit, then a Dremmel tool to enlarge the holes, so that the pillars just slid in an out of the stock. This allowed me to adjust them precisely before gluing in place and making the final adjustments to the sleeve. What is so great about this product is that you can precisely adjust the pillars to get the action of your rifle to lay perfectly in the stock with a perfect free float. Of course then I glass bedded the action, tang, and floor plate area. If you take your time, the product is very easy to use and the results will astound you as to how accurate a factory rifle can be when bedded properly.
N.º de producto: 080910000 BROWNELLS ADJUSTABLE PILLAR BEDDING SLEEVE Las mangas de bedding ajustables son fáciles de instalar y se adaptan a casi todos los tipos y tamaños de culatas de rifles. Los anillos de ajuste ligeros y pre-contorneados se desplazan sobre un eje completamente roscado, permitiéndote ajustarlos para un encaje exacto sin necesidad de cortes, limados o mecanizados adicionales y que consumen tiempo. Se venden en pares, el largo para el tornillo trasero y el corto para el tornillo delantero.
Las mangas de bedding ajustables se instalan fácilmente y se adaptan a casi todas las culatas de rifles, sin necesidad de cortes o mecanizados adicionales.
Incluyen anillos de ajuste ligeros y pre-contorneados que permiten un encaje exacto mediante un eje completamente roscado.
Se venden en pares, con una manga larga para el tornillo trasero y una corta para el tornillo delantero, y requieren modificaciones en la culata y el uso de bedding sintético.
Atributos
Peso de entrega: 0,027kgAltura de envío: 12mmAncho de envío: 80mmLongitud de envío: 196mm
Detalles del artículo
Hecho en USA
Operador económico responsable según el reglamento de la UE
Brownells España
P.I Molí d'en Xec / C.Barneda, 30
08291 Ripollet
España
info@brownells.es
¡Mejora tu rifle con las mangas de bedding ajustables de Brownells! 🛠️ Fáciles de instalar y perfectas para cualquier culata.
Inventory Just Two Sleeves & Fit All Types Of Stocks
Fully-adjustable bedding sleeves are easy to install and fit nearly all types and sizes of rifle stocks. Lightweight, pre-contoured adjustment rings move on a fully threaded shaft so you can size them for an exact fit without additional, time-consuming cutting, filing or machining. Sold as a pair, long for Rear screw, short for Front screw.
SPECS: Sleeve - steel, .296" (7.5mm) ID, 7/16"-20 tpi. Adjustment Ring - aluminum, .560" (14mm) OD. Front - .700" (17mm) long. Rear - 1.16" (2.9cm) long. Installation requires alterations to stock and synthetic bedding. Sold as pairs only.
Más...
Inventario Solo Dos Mangas & Se Ajustan a Todos los Tipos de Culatas
Las mangas de bedding ajustables son fáciles de instalar y se adaptan a casi todos los tipos y tamaños de culatas de rifles. Los anillos de ajuste ligeros y pre-contorneados se desplazan sobre un eje completamente roscado, permitiéndote ajustarlos para un encaje exacto sin necesidad de cortes, limados o mecanizados adicionales y que consumen tiempo. Se venden en pares, el largo para el tornillo trasero y el corto para el tornillo delantero.
ESPECIFICACIONES: Manga - acero, .296" (7.5mm) ID, 7/16"-20 tpi. Anillo de ajuste - aluminio, .560" (14mm) OD. Delantero - .700" (17mm) de largo. Trasero - 1.16" (2.9cm) de largo. La instalación requiere modificaciones en la culata y el uso de bedding sintético. Se venden únicamente en pares.
Más...
Evaluaciones de clientes para BROWNELLS ADJUSTABLE PILLAR BEDDING SLEEVE
Número de evaluaciones: 2
De brownells.com: 2
Evaluación media: 5
Works great.(20/06/2012)
I used these to pillar bed a pre 64 Winchester. They are great for someone who is doing a home job. They adjust a little to easy and would move when being placed in the hole. A dab of grease on the thread where the nuts are sitting will help. Make sure you have the correct size Forstner bit. I could not find a single local store that carries this size (9/16). If I could do it again I would get the piloted Forstner bit sold by Brownells (Stock #:080-909-000WB). It is not cheap, but it cost the same as a local machinist charged me to drill the holes in my stock. You could do it with a hand drill at home but these holes must be perfectly straight or you are defeating the purpose.
Phenomenal Product!(04/08/2013)
I recently used these for the first time on a Win Model 70 Super Grade, CRF, made in the 80's out of the CT plant. I have used Brownell's Acraglass Gel with steel ferrels for pillars for years on other rifles, but decided to try these adjustable pillars for this project. As the previous reviewer stated, getting the holes drilled precisely is critical. I used a 1/2" bit, then a Dremmel tool to enlarge the holes, so that the pillars just slid in an out of the stock. This allowed me to adjust them precisely before gluing in place and making the final adjustments to the sleeve. What is so great about this product is that you can precisely adjust the pillars to get the action of your rifle to lay perfectly in the stock with a perfect free float. Of course then I glass bedded the action, tang, and floor plate area. If you take your time, the product is very easy to use and the results will astound you as to how accurate a factory rifle can be when bedded properly.