Ayuda y contacto
Atributos
- Hacer: Beretta
- Modelo: 8000,92
- Peso de entrega: 0,005kg
- Ancho de envío: 83mm
- Longitud de envío: 146mm
(0) Cesta
Newsletters
Home
Partes de Armas cortas
Partes empuñaduras
Grip Bushings
BERETTA USA BUSHING, GRIP 8000/84F/92SER
Support
Consigue el Bushing Grip 8000/84F/92SER de Beretta USA para mejorar tu arma. 🔥 Perfecto para modelos 92 y 8000, ¡no te lo pierdas!
BERETTA USA BUSHING, GRIP 8000/84F/92SER
- Especificaciones:
- Hacer: Beretta
- Modelo: 92, 8000
15.9
15.9
1
EUR
15.9
EUR
0
15,90 €
Los precios incluyen el IVA, y el transporte de EE.UU a España, no incluye el envío a su domicilio.
N.º de producto: 913100488
Ref Fabricante: C50731
CASQUILLO, EMPUÑADURA 8000/84F/92SER
Reordenado
Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.
Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.
- Especificaciones:
- Hacer: Beretta
- Modelo: 92, 8000
Descripción:
Mostrar original (inglés)
COMPATIBLE CON: M9A1, 9 mm; Modelo 92; Modelo 92/96 FS Compact L, 9 mm, .40; Modelo 92/96 INOX, 9 mm
CASQUILLO, EMPUÑADURA 8000/84F/92SERAtributos
- Hacer: Beretta
- Modelo: 8000,92
- Peso de entrega: 0,005kg
- Ancho de envío: 83mm
- Longitud de envío: 146mm
Opiniones de clientes
Calificaciones de clientes (2)
5 / 5
Claramente recomendable
Taurus 92AF Perfect Fit 10/11/2017
I purchased these for my daughters Taurus 92AF. No issues what so ever. Went in without issue and no problems accepting the new Beretta screws.
Claramente recomendable
A Fine Bushing 16/09/2017
No issues with the bushing or bushing tool - both worked well. As Paul Harvey knew all too well, sometimes it's "the rest of the story". A grip screw broke off in my 92F and I accidentally damaged the bushing threads drilling out the screw. Lesson 1: don't use cheap grip screws (especially not the ones with pre-applied thread locker) Lesson 2: that screw hole is smaller than you think. The 92F has deeply staked bushings that are stubborn to remove, and if those frame threads get damaged, matters go from bad to worse. The bushing would not budge, and the bushing tool started deforming the bushing under increasing pressure. What to do? I filed the top of the bushing smooth (so the screw hole was clean and flush), then drilled the bushing with a 1/8" bit. A #2 screw extractor achieved adequate grip and torque to unscrew the bushing with no damage to the frame threads. The frame and new bushing were cleaned (de-greased) and installed using thread locking compound. Brownell's offers the staking head, but 3 of the 4 92F grip holes are indirect access, so the staking operation may require special equipment. Being able to add a little heat to loosen the thread locker for a "next time", seems the better option for an average Joe handyman.
<img width="500" src='/userdocs/reviewimages/28342aae-d0c6-4203-911a-82e419443828.jpg' alt=''>
Los clientes compraron
Reordenado
49,90 €
Vista clásica
Vista móvil