ADVANCED TECHNOLOGY
HEAT SHIELD

758152513007 019000004

Improves Control & Handling Convenience

Furnished with a complete set of adapters and spacers for installation on 12 gauge Mossberg 500, Maverick 88, Remington 870, and Winchester 1200/1300 pump shotguns. Easy to install, requires no modifications to firearm. Formed steel with elongated cooling slots protects your hands from burns. Provides a secure, non-slip, grasping surface, plus maximum heat dissipation. Simply slide over barrel and secure with supplied hardware. Black oxide finish matches most shotgun finishes. No gunsmithing required to fit most popular 12 gauge pump guns.

SPECS: Steel, black oxide, matte finish. 13¾ (35cm) long.

Más...

Mejora el Control y la Comodidad en el Manejo

Viene con un juego completo de adaptadores y separadores para su instalación en escopetas de bombeo de calibre 12 Mossberg 500, Maverick 88, Remington 870 y Winchester 1200/1300. Fácil de instalar, no requiere modificaciones en el arma de fuego. Acero conformado con ranuras de enfriamiento alargadas protege tus manos de quemaduras. Proporciona una superficie de agarre segura y antideslizante, además de una máxima disipación de calor. Simplemente desliza sobre el cañón y asegura con el hardware suministrado. El acabado en óxido negro combina con la mayoría de los acabados de escopetas. No se requiere de armero para adaptarse a las escopetas de bombeo de 12 gauge más populares.

ESPECIFICACIONES: Acero, acabado en óxido negro mate. 13¾ (35cm) de largo.

Más...

Evaluaciones de clientes para ADVANCED TECHNOLOGY HEAT SHIELD

Número de evaluaciones: 6
De brownells.com: 6
Evaluación media: 3,2

Solid Piece of Gear (16/09/2009)

Installed the Heat Shield on my Rem 870 in about 10 minutes and it fit with no alterations to the shield or the shotgun. Well constructed with an excellent pattern for heat dispersion. I would buy it again.

IVE BOUGHT A FEW OF THESE (13/04/2010)

IF YOU SHOOT A LOT OF SHELLS AND HAVE EVER BURNED YOUR HAND BY ACCIDENTALLY TOUCHING THE BARREL THIS ITEM IS FOR YOU. IT INSTALLS EASILY AND QUICKLY AND DOESN'T NEED TO BE REMOVED WHEN YOU CLEAN THE BORE OR BREAK DOWN YOUR SHOTGUN. IT ALSO ADDS A TOUGH LOOK TO THE SHOTGUN. IVE ONLY INSTALLED THIS ON MOSSBERG 500'S AND HAVE HAD NO PROBLEMS.

Difficult to install (21/01/2011)

Quality parts and manufacturing, but tricky to install on my 870 Tactical. Took some extra bending of the middle tabs and widening of the receiver-end of the shield to fit snug around my barrel. Had to file down the upper inside edge of the fore-end, as well, as the middle tabs were grinding on it upon cycling the action.

SHS-1300 Heat Shield by Advanced Technol (12/08/2011)

its plastic it belongs on my suns toy gun not on a tactical home protection shot gun, When i picked up my shot gun after i had installed the heat shield,the back of the heat shield came off of my shot gun due to the ring on the back of the heat shield is not a solid ring and it is flimsy and moves around on my shot gun. I do not recommend this product if you are serious about home defense or self protection. i recommend one made of steel.

1300 defender (05/03/2012)

*this may not apply to all shotguns* The fit and finish of the product is unacceptable. During install the heat shield heavily scratches the barrel's finish. The receiver end of the shield does not grip the barrel well allowing it to move and produce wear on the barrel. The forward end, with the two screw holes, comes to you flared out and out of alignment. This neccesitates a lot of test fits and alterations which again damages the finish of the gun. A gunsmith might have better luck with it. Mine found its way into the dumpster.

A good buy (25/01/2014)

This was an easy install, it is not a custom piece built specific to any gun, it is built to fit every 870 ever made. Take your time and you won't damage the finish on your weapon or on the heat shield. The instructions are pretty clear and easily followed (I read them afterwards) no modification was required to my weapon (H&R Pardner Protector Pump) even though I installed an 870 wood stock and forearm and a +2 magazine extension. The heat shield does require a little patience for a good tight fit but looks good after installation. It is a great deal for quality and looks, especially because it it metal and cost the same as some synthetic models

Leer 6 mas calificaciones en brownells.com

49.9 49.9 1 EUR

N.º de producto: 019000004
ADVANCED TECHNOLOGY HEAT SHIELD
Ref Fabricante: SHS1300 758152513007 Viene con un juego completo de adaptadores y separadores para su instalación en escopetas de bombeo de calibre 12 Mossberg 500, Maverick 88, Remington 870 y Winchester 1200/1300. Fácil de instalar, no requiere modificaciones en el arma de fuego. Acero conformado con ranuras de enfriamiento alargadas protege tus manos de quemaduras. Proporciona una superficie de agarre segura y antideslizante, además de una máxima disipación de calor. Simplemente desliza sobre el cañón y asegura con el hardware suministrado. El acabado en óxido negro combina con la mayoría de los acabados de escopetas. No se requiere de armero para adaptarse a las escopetas de bombeo de 12 gauge más populares.

49.9 EUR 99 49,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Caracteristicas: Hacer: Mossberg, Winchester, Remington, Maverick Modelo: 870, 500, 1300, 1200, 88

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

Compatible con escopetas de bombeo de calibre 12 Mossberg 500, Maverick 88, Remington 870 y Winchester 1200/1300, sin necesidad de modificaciones.
Fabricado en acero con ranuras de enfriamiento alargadas y acabado en óxido negro, protege las manos de quemaduras y proporciona una superficie de agarre segura.
Fácil de instalar deslizando sobre el cañón y asegurando con el hardware suministrado, sin necesidad de armero.

Atributos

Hacer: Maverick,Mossberg,Remington,Winchester Modelo: 1200,1300,500,870,88 Peso de entrega: 0,249kg Altura de envío: 30mm Ancho de envío: 51mm Longitud de envío: 467mm UPC : 758152513007