Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

BROWNELLS
PISTOL SCREWDRIVER SETS for GLOCK®

050806006171 080000447

Self-Storing, Carry Along For 'Smiths & Shooters

On the bench or in the field, you’ll have the right screwdrivers for your gun in one compact, go-anywhere package. We precisely matched each gun’s screws to the correct Magna-Tip® bits to give you the best possible, blade-to-slot fit. Except where indicated otherwise, each set comes with a magnetic socket, Hollow Handle for easy, on-board storage of the bits. Two takedown bits for pistol itself and magazine, plus three bits and a .050" Allen wrench for adjustable aftermarket sights.

SPECS: 6-3⁄16" (15.7cm) long overall. 1¼” (3.2cm) diameter grip.

Más...

Autoalmacenables, Para Llevar por Armeros y Tiradores

Tanto en el taller como en el campo, tendrás los destornilladores adecuados para tu arma en un paquete compacto que puedes llevar a cualquier parte. Hemos emparejado con precisión los tornillos de cada arma con las puntas Magna-Tip® correctas para ofrecerte el mejor ajuste posible de la hoja con la ranura. Excepto donde se indique lo contrario, cada conjunto viene con un casquillo magnético, Mango Hueco para un fácil almacenamiento a bordo de las puntas. Dos puntas para desmontar la pistola y el cargador, además de tres puntas y una llave Allen de .050" para miras ajustables aftermarket.

ESPECIFICACIONES: 6-3⁄16" (15.7cm) de largo en total. Diámetro del agarre de 1¼” (3.2cm).

Más...

Evaluaciones de clientes para BROWNELLS SCREWDRIVER BITS ONLY FOR GLOCK

Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 3

Nice multi-tool (12/11/2009)

Nice tool for the armorer or do-it-yourself guy/gal. The screwdriver body is okay, standard plastic body (cheap), but it does have a magnet in the shaft, so your bits stay in nice and tight. I wasn't able to fit all the bits into the body of the screwdriver, one bit had to remain in the shaft.

All in all, it's a great tool. Knowing what I know now, I would probably just buy the bits and use them in my own screwdriver.

Oh well, either way works!

Very disappointing "Tool Set" (28/01/2010)

I am a certified Glock armorer for a Department of Defense Law Enforcement unit. I bought this Screwdriver set as an alternative to small, hard to use tools to install after-market front sights on Glocks. It was a little pricey, but I've been using Brownell's Gunsmithing Screwdrivers exclusively for years, so I assumed it was worth it.

How wrong I was. First of all, there are five bits and one Allen wrench in this kit. Only two of the five bits have any real utility for Glock pistols (unless you're one of the very few people still running their adjustable rear sights, then the thin-bladed straight screwdriver bit could be handy.) The Allen wrench serves no purpose in mainteance of a Glock. There are two round punches, only one of which is appropriately sized for any use in maintenance of any Glock model. To top it off, it's nearly impossible to get all of the bits (because there are too many, most of which are unnecessary) into the handle of the screw driver for storage.

The worst part is the bit that is the whole reason I bought this set - the front sight screw bit. First of all, it is bored too deeply. When you put a front sight screw into it, it will "sink" into the bit's body at an angle at the first instance of attempting to put any pressure on it (e.g. when you try to start the screw). I called Brownell's tech support about this, thinking I must have gotten a bad bit, and was told that my bit was made "to spec." I was further told that, in order to use the bit to install the front sight screw, I should first "start the screw" by putting petroleum jelly on a pencil eraser, sticking the front sight screw to the eraser, and using it to get the screw initially threaded. The technician said all this as if it is standard procedure in the industry to use that method, which, I can attest, it is not. So, basically, this is a nut-driver bit with which you cannot drive the nut that needs to be installed. Great.

Fast forward about eight months to today. I have used this "tool" to uninstall about 10 sets of Glock sights, at an outside extreme (probably more like six). I attempted to use it this morning to remove a front sight screw that had been installed, IAW Glock and the manufacturer's instructions, with a small amount of Blue Loctite. I fitted the nut-driver over the end of the nut, started to turn the handle, and the bit broke! The mouth of the bit snapped off - without budging the hand-tight and Blue-loctited screw.

All in all, I couldn't be more disappointed in this set. If you're considering it, please save your money and look elsewhere.

I should've listened to the reviews (04/08/2011)

Cheap feeling, handle too tight and short to handle the contents of the kit, bits wobble and fall out too easily. Do youself a favor and listen to the reviews!

Great buy! (31/01/2012)

Im not sure what some of these other guys are working on but I have found this tool to be the Perfect Glock tool. The front sight tool works as it should with no problems and I have used it on 25-30 guns in the past 2-3 months. The take down tool works, the other punch is great for the magazines as its a bit longer than the standard punch. When your changing out base pads or springs in mags it is handy. The small screw driver is great for guns with Glock factory adjustable sights. The allen wrench and hex bit work great for aftermarket sights that require a bit to tighten them down. This tool plus my Glock sight pusher is all I ever need. I too am a Certified Glock Armorer and I love this tool!

Works for Most Glock Tasks (26/10/2017)

Agree with Chris from Iowa. Don't know what these other guys are working on.

Used the Front Sight hex tool to replace front sight w/ Tru-Glo TFX on G43. I own a Glock front sight tool which would be my first choice but this one works fine. Used MGW Glock pusher w/adapter to remove and replace rear sight w/ TFO then used small Allen bit to tighten small Allen set screw.

Small punch will work on all disassembly pins but wish they included a larger punch for the larger trigger pin.

Have used the larger punch on Glock Extended mag plates like the Pearce and Standard Glock along with a GTUL and Vise Grips to compress the magazine bodies so as not to damage the tabs. On standard and flat aftermarket Glock baseplates, I use the GTUL along with the MagClaw.

Used the small standard screwdriver bit to remove and replace the mag release spring for R&R of ambi mag release (G43). Worked well.

ALL bits will fit into handle IF you put them back in the correct order. Put the Allen wrench in first short side down, sight tool, large punch & small Allen bit (fat driver side down), small punch and screw driver bit (fat driver side up). Place cap on and jiggle (don't force) until threads engage. Tilt the driver handle and jiggle as you tighten the cap. Voila!

Leer 5 mas calificaciones en brownells.com

31.9 49.9 2 EUR

N.º de producto: 080000447
BROWNELLS SCREWDRIVER BITS ONLY FOR GLOCK 050806006171 Tanto en el taller como en el campo, tendrás los destornilladores adecuados para tu arma en un paquete compacto que puedes llevar a cualquier parte. Hemos emparejado con precisión los tornillos de cada arma con las puntas Magna-Tip® correctas para ofrecerte el mejor ajuste posible de la hoja con la ranura. Excepto donde se indique lo contrario, cada conjunto viene con un casquillo magnético, Mango Hueco para un fácil almacenamiento a bordo de las puntas. Dos puntas para desmontar la pistola y el cargador, además de tres puntas y una llave Allen de .050" para miras ajustables aftermarket.

31.9 EUR 0 31,90 € *

Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.

Caracteristicas: Hacer: Glock Modelo: Universal Handguns

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

Conjunto compacto de destornilladores diseñado específicamente para armas Glock, ideal tanto para el taller como para el campo.
Incluye puntas Magna-Tip® precisas y un casquillo magnético, además de un Mango Hueco para almacenamiento fácil de las puntas.
Contiene dos puntas para desmontar la pistola y el cargador, tres puntas adicionales y una llave Allen de .050" para miras ajustables aftermarket.

Atributos

Hacer: Glock Modelo: Universal Handguns Peso de entrega: 0,034kg Ancho de envío: 83mm Longitud de envío: 146mm UPC : 050806006171

Detalles del artículo

Hecho en USA

N.º de producto: 080000408
BROWNELLS SCREWDRIVER SET FOR GLOCK 050806006072 Tanto en el taller como en el campo, tendrás los destornilladores adecuados para tu arma en un paquete compacto que puedes llevar a cualquier parte. Hemos emparejado con precisión los tornillos de cada arma con las puntas Magna-Tip® correctas para ofrecerte el mejor ajuste posible de la hoja con la ranura. Excepto donde se indique lo contrario, cada conjunto viene con un casquillo magnético, Mango Hueco para un fácil almacenamiento a bordo de las puntas. Dos puntas para desmontar la pistola y el cargador, además de tres puntas y una llave Allen de .050" para miras ajustables aftermarket.

49.9 EUR 0 49,90 € *

Pedido pendiente, tiempo de entrega aproximado 4-12 semanas desde el almacén de EE. UU.

Caracteristicas: Estilo: 5-Bits Hacer: Glock Manejo: 84 Hollow Modelo: Universal Handguns

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Consigue el set de destornilladores PISTOL para GLOCK® 🛠️, ideal para el taller y el campo. Compacto y preciso, ¡no te quedes sin el tuyo!

Self-Storing, Carry Along For 'Smiths & Shooters

SPECS: 6-3⁄16" (15.7cm) long overall. 1¼” (3.2cm) diameter grip.

Más...

Autoalmacenables, Para Llevar por Armeros y Tiradores

ESPECIFICACIONES: 6-3⁄16" (15.7cm) de largo en total. Diámetro del agarre de 1¼” (3.2cm).

Más...

Evaluaciones de clientes para BROWNELLS SCREWDRIVER BITS ONLY FOR GLOCK

Número de evaluaciones: 5
De brownells.com: 5
Evaluación media: 3

Nice multi-tool (12/11/2009)

Very disappointing "Tool Set" (28/01/2010)

I should've listened to the reviews (04/08/2011)

Cheap feeling, handle too tight and short to handle the contents of the kit, bits wobble and fall out too easily. Do youself a favor and listen to the reviews!

Great buy! (31/01/2012)