Su cesta está vacía.

Cesta

Ayuda y contacto

Envío gratuito a partir de 200 €

Política de devolución de 100 días

Newsletters

Oferta

Más de 300,000 clientes - ¡les damos las gracias!

4,93/5 "Muy bueno" (1400+ reseñas)

40,000+ productos para caza y deportes de tiro

SINCLAIR/L.E. WILSON
STAINLESS STEEL CASE TRIMMER KIT

749011888

L.E. Wilson Case Trimmer and Sinclair Mounting Stand with “SharkFin” Case Holder Clamp (order case holders separately.) This mounting stand and clamping attachment make case trimming much quicker and comfortable. The mounting stand can be C-clamped or permanently mounted to a bench top. The “SharkFin” Case Holder Clamp swings quickly into place and provides downward pressure on the case holder while trimming.

Más...

Recortadora de vainas L.E. Wilson y soporte de montaje Sinclair con abrazadera para sujetar vainas "SharkFin" (comprar soportes para vainas por separado). Este soporte de montaje y accesorio de sujeción hacen que el recorte de vainas sea mucho más rápido y cómodo. El soporte de montaje se puede sujetar con una abrazadera en C o montar de forma permanente en la superficie de trabajo. La abrazadera para sujetar vainas "SharkFin" se coloca rápidamente en su lugar y ejerce presión hacia abajo sobre el soporte de la vaina durante el recorte.

Más...

Evaluaciones de clientes para SINCLAIR/L.E. WILSON STAINLESS TRIMMER WITH STAND & SHARK FIN CLAMP

Número de evaluaciones: 7
De brownells.com: 7
Evaluación media: 3,7

Poor Finish (25/01/2011)

The finish was poor compared to the picture on the cover of my catalog. The base of the cutter was throughly pitted across the entire surface, a case holder was also lightly pitted. The cuts in the base to retain the two long thin rods had rough machining marks. The hole in the trimmer stand for the "sharkfin" still had metal burrs protruding which needed to be removed. The Sinclair case holder adapter had scuff marks from the two long thin rods which made it look like I was sent a used part. None of this was major enough to effect function, but due to the cost, it is somewhat disappointing.

one of its kind (27/03/2011)

the design is perfect but I wish they sell these from the start with the ergonomic crank handle.I fixed my problem by putting rubber on the handle so it won't hurt my hand.

Perfect out of the box! (20/04/2011)

This accessory is great. It assembled flawlessly and the shark fin required no adjustment to get rolling. It's a pleasure working with perfect tools.

Excellent (04/10/2011)

It's hard to beat Wilson tools of any kind, and this trimmer is no exception. I've had mine for about 2 years now, and it still functions flawlessly. This trimmer differs from all others in that it uses case holders and you'll need to purchase the specific one(s) for each caliber(s). This all but eliminates wobble, mis-alignment, etc., as the case is perfectly centered. I was reluctant to purchase this trimmer for this reason, but I'm glad I did.

Great Trimmer, No attaching screws? (24/08/2012)

The Wilson trimmer works great. It is easy to adjust and set up. It cuts square and to a consistent length. I only have one minor negative thing, that isn't a reflection of the trimmer. When I got mine it did not come with screws to attach the base to the trimmer. It was an easy fix, I had to get two hex head screws that are 10-32 thread pitch. I had to buy one inch long screws and cut them down to about .875 to get them to the proper length to attach the trimmer to the base. It would have been nice to have the screws included. Maybe I was just unlucky and they usually are, I don't know. That being said I would highly recommend it.

Difficult to adjust (11/09/2017)

When I got it, I was impressed with it, the construction quality is good and it looks nice. I read the instructions well and it seems straightforward in the instructions. It does cut the case mouths nice and square, I will give it that. Very very square. However, I have found it a poor case trimmer, because it is extremely difficult to set a repeatable case trim length. I will set it up for .223 Remington, for example at trim length of 1.750. Afterwards, case lengths will be all over the place. Its super sensitive to set up for case length and very sensitive to both how tight the set screw is as well as hand pressure on the handle while cranking it. I dont use it.

Problems 2 case (21/06/2018)

Very nice looking trimmer but on my second case the handle fell off the crank. I can't get it screwed back on because the handle and the screen I side it rotate separately of each other.

Leer 7 mas calificaciones en brownells.com

224.9 224.9 1 EUR

N.º de producto: 749011888
SINCLAIR/L.E. WILSON STAINLESS TRIMMER WITH STAND & SHARK FIN CLAMP Recortadora de vainas L.E. Wilson y soporte de montaje Sinclair con abrazadera para sujetar vainas "SharkFin" (comprar soportes para vainas por separado). Este soporte de montaje y accesorio de sujeción hacen que el recorte de vainas sea mucho más rápido y cómodo. El soporte de montaje se puede sujetar con una abrazadera en C o montar de forma permanente en la superficie de trabajo. La abrazadera para sujetar vainas "SharkFin" se coloca rápidamente en su lugar y ejerce presión hacia abajo sobre el soporte de la vaina durante el recorte.

224.9 EUR 3 224,90 € *

Plazo de entrega de aproximadamente 14-21 días.

Añadir a la lista de favoritos.

Preguntas

Detalles

Añadir a la lista de favoritos.

Preguntas

Top takeaways

La recortadora de vainas L.E. Wilson y el soporte de montaje Sinclair incluyen una abrazadera "SharkFin" para sujetar vainas.
El soporte de montaje puede fijarse con una abrazadera en C o montarse de forma permanente en la superficie de trabajo.
La abrazadera "SharkFin" facilita y acelera el proceso de recorte al ejercer presión hacia abajo sobre el soporte de la vaina.

Atributos

Peso de entrega: 0,975kg Altura de envío: 102mm Ancho de envío: 127mm Longitud de envío: 191mm

Detalles del artículo

Hecho en USA

¡Haz el recorte de vainas más fácil! ✂️ Con el kit de trimmer de acero inoxidable de Sinclair y L.E. Wilson, obtén precisión y comodidad.

Más...

Evaluaciones de clientes para SINCLAIR/L.E. WILSON STAINLESS TRIMMER WITH STAND & SHARK FIN CLAMP

Número de evaluaciones: 7
De brownells.com: 7
Evaluación media: 3,7

Poor Finish (25/01/2011)

one of its kind (27/03/2011)

the design is perfect but I wish they sell these from the start with the ergonomic crank handle.I fixed my problem by putting rubber on the handle so it won't hurt my hand.

Perfect out of the box! (20/04/2011)

This accessory is great. It assembled flawlessly and the shark fin required no adjustment to get rolling. It's a pleasure working with perfect tools.

Excellent (04/10/2011)

Great Trimmer, No attaching screws? (24/08/2012)

Difficult to adjust (11/09/2017)

Problems 2 case (21/06/2018)

Very nice looking trimmer but on my second case the handle fell off the crank. I can't get it screwed back on because the handle and the screen I side it rotate separately of each other.

Leer 7 mas calificaciones en brownells.com